Visual Comfort Mf 5052 Extra Large Dome Hanging Shade Instruction Manual

MF 5052 Extra Large Dome Hanging Shade

Product Information

Product Name: Whit Extra Large Dome Hanging Shade

Item Number: MF 5052

Notice

This light fixture should be installed in accordance with all
applicable, local installation codes, and by a person familiar with
the construction and operation of it, as well as the hazards
involved. Inspect item and contents carefully. If any damage or
defect is found, do not install. Retain all packaging material
until installation is complete and approved.

Tools Required (Not Included)

• Phillips Screwdriver
• Slotted Screwdriver
• Slip Joint Pliers
• Measuring Tape
• Wire Strippers
• Chain Pliers
• Wire Cutters

Product Usage Instructions

1. Carefully remove all parts from the box. Place on a clean, soft
   surface.
2. Remove collar loop (C) from chain (H) by removing quick link
   (G).
3. Install mounting plate (B) to the junction box and secure with
   mounting screws (D).
4. Secure collar loop (C) to mounting plate (B) using pliers to
   tighten locknut.
5. Install canopy (E) to collar loop (C) and secure with collar
   ring (F).
6. Determine desired overall length and amount of chain (H)
   needed. Shorten chain using chain pliers. Keep extra chain.
7. Attach chain (H) to fixture loop (K) and secure threaded cap
   (J). See diagram 1.
8. Feed chain (H) through shade (I), then holding fixture upright,
   slide shade (I) down and rest on fixture.
9. Attach chain (H) to collar loop (C) using quick link (G).
   Secure quick link (G).
10. Thread fixture wire and ground wire through chain (H). Note:
    When you reach the collar loop (C), ensure there is no tension on
    the wires. Cut excess wires, being sure to leave enough to reach
    the junction box.
11. Separate two sides of molded wire and strip insulation on each
    5/8.
12. Loosen collar ring (F) and let canopy (E) slip down chain (H)
    carefully.
13. Twist all fixture wires together. Slip through center hole of
    collar loop (C). Note: Untwist wires and separate to prepare for
    connection.
14. Wrap fixture ground wire (bare copper) around the green
    grounding screw (see diagram 2). Tighten. Continue fixture ground
    wire and connect to supply ground wire (usually green or bare
    copper) using wire nut (A). Note: It is imperative that the fixture
    is grounded.
15. Connect fixture neutral wire (ribbed) to the supply neutral
    wire (usually white) using wire nut (A).
16. Connect fixture hot wire (smooth with markings) to the supply
    hot wire (usually black) using wire nut (A). Caution: Do not
    reverse the hot and neutral connections.
17. Make sure all wire connections are tight, then carefully tuck
    into the junction box.
18. Install canopy (E) to collar loop (C) and secure with collar
    ring (F).
19. Install light bulb into the socket.
20. Thread glass shade (L) to fixture.

ASSEMBLY INSTRUCTIONS

Diagram 2

A
B C D E F G H

H J
Diagram 1

I K Bulbs not included L

Whit Extra Large Dome Hanging Shade
Item # MF 5052
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver

Slotted Screwdriver

Slip Joint Pliers

Measuring Tape

Wire Strippers

Chain Pliers Wire Cutters

1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove collar loop (C) from chain (H) by removing quick link (G). 3. Install mounting plate (B) to the junction box and secure with
mounting screws (D). 4. Secure collar loop (C) to mounting plate (B) using pliers to tighten
locknut. 5. Install canopy (E) to collar loop (C) and secure with collar ring (F). 6. Determine desired overall length, and amount of chain (H) needed.
Shorten chain using chain pliers. (Keep extra chain) 7. Attach chain (H) to fixture loop (K). Secure threaded cap (J).
See diagram 1. 8. Feed chain (H) though shade (I), then holding fixture upright, slide
shade (I) down and rest on fixture. 9. Attach chain (H) to collar loop (C) using quick link (G). Secure quick
link (G). 10. Thread fixture wire and ground wire through chain (H).
NOTE: When you reach the collar loop (C), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 11. Separate two sides of molded wire, and strip insulation on each 5/8″. 12. Loosen collar ring (F) and let canopy (E) slip down chain (H) carefully.

M

LI ST ED

US

LED

ASSEMBLY INSTRUCTIONS

Diagram 2

A
B C D E F G H

H J
Diagram 1

I K Bulbs not included L

Whit Extra Large Dome Hanging Shade
Item # MF 5052
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
13. Twist all fixture wires together. Slip through center hole of collar loop (C). NOTE: Untwist wires and separate to prepare for connection.
14. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
15. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
16. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
17. Make sure all wire connections are tight, then carefully tuck into the junction box.
18. Install canopy (E) to collar loop (C) and secure with collar ring (F). 19. Install light bulb into the socket. 20. Thread glass shade (L) to fixture.
NOTE: Do not over-tighten otherwise shade could become damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

M

LI ST ED

US

LED