ARN 5510 Casoria Large Linear Chandelier

Product Information

Product Name: Casoria Large Linear
Chandelier

Item Number: ARN 5510

Package Contents: Chandelier fixture body,
mounting plate (A), canopy (G), bottom rods (J, K), top rod (I),
glass panels (M), rubber washers (N), screws (H, O), caps (P), wire
nut (C)

Tools Required (Not Included): Phillips
Screwdriver, Slotted Screwdriver, Wire Strippers, Wire Cutters

Notice: This light fixture should be installed
in accordance with all applicable, local installation codes, and by
a person familiar with the construction and operation of it, as
well as the hazards involved. Inspect item and contents carefully.
If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.

Product Usage Instructions

1. Carefully remove all parts from the box and place them on a
   clean, soft surface.
2. Loosen screws (H) to remove mounting plate (A) from canopy
   (G).
3. Install mounting plate (B) to the junction box and secure it
   with mounting screws (B).
4. Feed electrical wires through bottom rod (K) and connect them
   to the fixture body (L). Repeat this step for rod (J), connecting
   it to bottom rod (K).
5. Feed electrical wires through canopy (G) and top rod (I).
6. Holding the fixture upright, slide the canopy (G) down and rest
   it on coupling M.
7. Connect the fixture neutral wire (white) to the supply neutral
   wire (usually white) using wire nut (C).
8. Connect the fixture hot wire (black) to the supply hot wire
   (usually black) using wire nut (C). CAUTION: Do
   not reverse the hot and neutral connections.
9. Ensure all wire connections are tight, then carefully tuck them
   into the junction box.
10. Install the canopy (G) to the mounting plate (A) and secure it
    with screws (H).
11. Install light bulbs into the sockets.
12. Attach glass panels (M) and rubber washers (N) to the socket
    and secure them with screws (O) and caps (P).
    NOTE: Do not overtighten, otherwise, the shade
    could become damaged.

Care Instructions

Clean the chandelier only with a soft dry cloth or feather
duster. Do not use abrasive or chemical agents.

ASSEMBLY INSTRUCTIONS
A C D
E D Diagram 1

B G
H I J K
L

Diagram 2
Bulbs not included M N O P

Casoria Large Linear Chandelier
Item # ARN 5510
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver

Slotted Screwdriver

Wire Strippers

Wire Cutters

1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (A) from canopy (G) by loosening screws (H). 3. Install mounting plate (B) to the junction box and secure with
mounting screws (B). 4. Feed electrical wires through bottom rod (K) and connect to fixture
body (L). Repeat for rod (J), connecting to bottom rod (K). 5. Feed electrical wires through canopy (G) and top rod (I). 6. Holding fixture upright, slide canopy (G) down and rest on coupling
located on top of rod (J). Then connect top rod (I) to rod (J). NOTE: Slide components down slowly to avoid damages. 7. Hang fixture metal plate (D) to center of mounting plate (A). See diagram 1. NOTE: If needed, adjust fixture balance by securing or loosening screws (E) on mounting plate (A). 8. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″. 9. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (C). NOTE: It is imperative that the fixture is grounded.

M

LI ST ED

US

ASSEMBLY INSTRUCTIONS
A C D
E D Diagram 1

B G
H I J K
L

Diagram 2
Bulbs not included M N O P

Casoria Large Linear Chandelier
Item # ARN 5510
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
10. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (C).
11. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (C). CAUTION: Do not reverse the hot and neutral connections.
12. Make sure all wire connections are tight, then carefully tuck into the junction box.
13. Install canopy (G) to mounting plate (A) and secure with screws (H). 14. Install light bulbs into the sockets. 15. Attach glass panels (M) and rubber washers (N) to socket and secure
with screws (O) and caps (P). NOTE: Do not overtighten otherwise shade could become damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

M

LI ST ED

US