IKF 5362 Mafra XL Chandelier
Product Information
- Product Name: Mafra XL Chandelier
- Item Number: IKF 5362
Notice: This light fixture should be installed
in accordance with all applicable, local installation codes, and by
a person familiar with the construction and operation of it, as
well as the hazards involved. Inspect item and contents carefully.
If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.
Tools Required (Not Included):
- Phillips Screwdriver
- Wire Cutters
- Slotted Screwdriver
- Wire Strippers
- Measuring Tape
Persons Required: Two
Product Usage Instructions
- Carefully remove all parts from the box. Place on a clean, soft
surface. - Remove mounting plate (D) from canopy (E) by unscrewing.
- Install mounting plate (D) to junction box and secure with
mounting screws. - Connect driver (B) output neutral wire (black) to the fixture
neutral wire (marked -) using wire nut (A). - Connect driver (B) output hot wire (red) to the fixture hot
wire (marked +) using wire nut (A). Caution: Do
not reverse the hot and neutral connections. - Connect supply ground wire (usually green or bare copper)
around the green grounding screw (see diagram 2). Tighten.
Note: It is imperative that the fixture is
grounded. - Connect driver (B) input neutral wire (white) to the supply
neutral wire (usually white) using wire nut (A). - Connect driver (B) input hot wire (black) to the supply hot
wire (usually black) using wire nut (A). Caution:
Do not reverse the hot and neutral connections. - Make sure all wire connections are tight, then carefully tuck
into the junction box. - Install driver (B) into mounting plate bracket (D).
- Thread canopy (E) to mounting plate (D).
- Remove protective covers (H) from sockets.
- Install LED bulbs (G) to sockets.
- Thread shades (F) to fixture body (I). Note:
Do not overtighten otherwise shade could become damaged.
Care Instructions: Clean only with a soft dry
cloth or feather duster. Do not use abrasive or chemical
agents.
ASSEMBLY INSTRUCTIONS
Diagram 2
KL D
J Diagram 1
A B C
E
White
Black
Input
N
L
Output
Black
Red
F
G
H I
Mafra XL Chandelier
Item # IKF 5362
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Wire Cutters
Slotted Screwdriver Wire Strippers
Measuring Tape
PERSONS REQUIRED: Two
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (D) from canopy (E) by unscrewing. 3. Install mounting plate (D) to junction box and secure with mounting
screws (C). NOTE: It is recommended to have a helper assist in supporting the fixture for steps 4-5. 4. Feed hanging cables through canopy (E), then insert through holes on bottom of mounting plate (D). 5. Install cable locks (L) to end of hanging cables. Insert hanging cable through other end of locks and tighten ends (K) with screwdriver (J) to secure. See diagram 1. 6. Adjust hanging cables to desired height and level fixture. NOTE: Double check height and ensure fixture is level before moving to next step. 7. Cut excess wires, being sure to leave enough to reach the junction box. Separate fixture wires (marked “+” & “-“) and strip insulation on each 5/8”.
ASSEMBLY INSTRUCTIONS
Diagram 2
KL D
J Diagram 1
A B C
E
White
Black
Input
N
L
Output
Black
Red
F
G
H I
Mafra XL Chandelier
Item # IKF 5362
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
8. Connect driver (B) output neutral wire (black) to the fixture neutral wire (marked “-“) using wire nut (A).
9. Connect driver (B) output hot wire (red) to the fixture hot wire (marked “+”) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
10. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten. NOTE: It is imperative that the fixture is grounded.
11. Connect driver (B) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
12. Connect driver (B) input hot wire (black) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
13. Make sure all wire connections are tight, then carefully tuck into the junction box.
14. Install driver (B) into mounting plate bracket (D). 15. Thread canopy (E) to mounting plate (D). 16. Remove protective covers (H) from sockets. 17. Install LED bulbs (G) to sockets. 18. Thread shades (F) to fixture body (I).
NOTE: Do not overtighten otherwise shade could become damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
