Visual Comfort Arn 5486 Casoria Grande Two Tier Chandelier Instruction Manual (+ PDF)

Home » Blog » Visual Comfort Arn 5486 Casoria Grande Two Tier Chandelier Instruction Manual

Contents hide

1 ARN 5486 Casoria Grande Two Tier Chandelier

2 Product Information

3 Product Usage Instructions

3.1 Documents / Resources

ARN 5486 Casoria Grande Two Tier Chandelier

Product Information

Product Name: Casoria Grande Two Tier
Chandelier

Item Number: ARN 5486

Usage: This two-tier chandelier is designed to
provide ambient lighting in residential or commercial spaces. It
should be installed in accordance with local installation codes by
a person familiar with its construction and operation.

Important Notice: Inspect the item and its
contents carefully before installation. If any damage or defect is
found, do not install. Retain all packaging material until
installation is complete and approved.

Tools Required (Not Included):

Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Measuring Tape
Wire Strippers
Chain Pliers Wire Cutters

Persons Required: Two

Product Usage Instructions

Carefully remove all parts from the box and place them on a
clean, soft surface.
Rotate the fixture arms into position as shown in Diagram 1,
spacing each part correctly.
Feed the fixture wires from the bottom tier (J2) through the
hub (R).
Connect the top tier neutral wire (ribbed) to the bottom tier
neutral wire (ribbed) using a wire nut (U).
Connect the top tier hot wire (smooth with markings) to the
bottom tier hot wire (smooth with markings) using a wire nut
(U).
Install the hub (R) and bottom tier (J2) to the threaded tube
(S) and secure them with a hex nut (V) using the provided wrench
(W).
Thread the finial (O) to the bottom of the tier (J2).
Thread the fixture wire and ground wire through the chain
(G).
Connect the fixture hot wire (smooth with markings) to the
supply hot wire (usually black) using a wire nut (A).
Caution: Do not reverse the hot and neutral
connections.
Make sure all wire connections are tight, then carefully tuck
them into the junction box.
Install the canopy (E) to the collar loop (D) and secure it
with the collar ring (F).
Install light bulbs into the sockets.
Attach glass panels (L) and rubber washers (K) to the socket
cup and secure them with screws (M) and caps (N).
Note: Do not overtighten, as it could damage the
glass.

Care Instructions: Clean the chandelier only
with a soft dry cloth or feather duster. Do not use abrasive or
chemical agents.

Please refer to the user manual for additional information
and safety guidelines.

View Fullscreen

ASSEMBLY INSTRUCTIONS
Top & Bottom tier B

Diagram 1

A C D H E F
Bulbs not included

S U
R

L J1

K MN

V O
W

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver

Slotted Screwdriver

Slip Joint Pliers

Measuring Tape

Wire Strippers

Chain Pliers Wire Cutters

PERSONS REQUIRED: Two

1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Rotate fixture arms into position as shown in diagram 1, spacing each
arm evenly for top & bottom tiers. NOTE: If needed, tighten hex nuts on arms using provided wrench (W). 3. Remove collar loop (D) from chain (G) by unscrewing quick link (H). 4. Install mounting plate (B) to junction box and secure with mounting screws (C). 5. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut. 6. Install canopy (E) to collar loop (D) by securing and secure with collar ring (F). 7. Determine desired overall length, and amount of chain (G) needed. Shorten chain using chain pliers. (Keep extra chain) 8. Feed fixture wire and ground wire through tube (P) and connect to top tier (J1). 9. Attach chain (G) to collar loop (D) and to fixture loop (I) using quick links (H). Secure quick links (H). 10. Install threaded tube (S) to hickey (Q) using pliers to tighten locknut. NOTE: It is recommended to have a helper assist in supporting the fixture for steps 11-14.

L IS T ED

ASSEMBLY INSTRUCTIONS
B
Diagram 2 G H I P

A C D H E F
Bulbs not included

L K MN

J1 S U

R J2

V O
W

Casoria Grande Two Tier Chandelier
Item # ARN 5486
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
11. Feed fixture wires from bottom tier (J2) through hub (R). 12. Connect top tier neutral wire (ribbed) to bottom tier neutral wire
(ribbed) using wire nut (U). 13. Connect top tier hot wire (smooth with markings) to bottom tier
hot wire (smooth with markings) using wire nut (U). 14. Install hub (R) and bottom tier (J2) to threaded tube (S) and secure
with hex nut (V) using provided wrench (W). 15. Thread finial (O) to the bottom of tier (J2). 16. Thread fixture wire and ground wire through chain (G).
NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 17. Separate two sides of molded wire, and strip insulation on each 5/8″. 18. Loosen collar ring (F) and let canopy (E) slip down chain (G) carefully. 19. Twist all fixture wires together. Slip through center hole of collar loop (D). NOTE: Untwist wires and separate to prepare for connection. 20. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded. 21. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).

L IS T ED

ASSEMBLY INSTRUCTIONS
B
Diagram 2 G H I P

A C D H E F
Bulbs not included

L K MN

J1 S U

R J2

V O
W

L IS T ED