JN 5313 Alberto Large Linear Chandelier
Product Information:
Product Name: Alberto Large Linear Chandelier
Model Number: JN 5313
Manufacturer: [Manufacturer Name]
Included Items: Chandelier fixture, mounting plate, collar rings,
canopy, chains, quick links, wire nuts, anchors, screws, tools
required (not included)
Product Usage Instructions:
- Carefully remove all parts from the box and place them on a
clean, soft surface. - Use the mounting plate (C) as a guide and line it up with the
junction box. Mark the anchor positions. - Using a drill bit slightly smaller than the anchor, drill holes
in the marked positions. Install anchors (B) into the holes using a
hammer. - Install the mounting plate (C) to the junction box and secure
it with mounting screws (E). Then, secure wood screws (D) to the
anchors (B). - Remove collar rings (I) from collar loops (F).
- Install the canopy (H) to the mounting plate (C) and secure it
with collar rings (I). - Determine the desired overall length and the amount of chains
(J) needed. Shorten the chain using chain pliers. Keep any extra
chain. - Attach chains (J) to collar loops (F) and fixture loops (K)
using quick links (G). Secure the quick links (G). - Thread the fixture wire and ground wire through the chain (J).
Make sure there is no tension on the wires when reaching the collar
loop (F). Cut any excess wires, leaving enough to reach the
junction box. - Separate the two sides of the molded wire and strip insulation
on each side by 5/8. - Loosen collar rings (I) and carefully let the canopy (H) slip
down the chains (J). - Twist all fixture wires together and slip them through the
center hole of the collar loop (F). Untwist and separate the wires
to prepare for connection. - Wrap the fixture ground wire (bare copper) around the green
grounding screw. Tighten it. Continue the fixture ground wire and
connect it to the supply ground wire (usually green or bare copper)
using a wire nut (A). - Connect the fixture neutral wire (ribbed) to the supply neutral
wire (usually white) using a wire nut (A). - Connect the fixture hot wire (smooth with markings) to the
supply hot wire (usually black) using a wire nut (A). Do not
reverse the hot and neutral connections. - Ensure all wire connections are tight, then carefully tuck them
into the junction box. - Install the canopy (H) to the mounting plate (C) and secure it
with collar rings (I).
ASSEMBLY INSTRUCTIONS
Diagram 1
Alberto Large Linear Chandelier
Item # JN 5313
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
B
Retain all packaging material until installation is complete and approved.
C
E
F
A
D
G
H
I J
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Wire Strippers
Wire Cutters
Drill
Pencil
Chain Pliers Measuring Tape
Hammer
1. Carefully remove all parts from the box. Place on a clean, soft surface.
G K
2. Using the mounting plate (C) as a guide, line up with the junction box and mark anchor positions.
3. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (B) into the holes using hammer.
4. Install mounting plate (C) to the junction box and secure with
mounting screws (E), then secure wood screws (D) to anchors (B).
Bulbs not included
5. Remove collar rings (I) from collar loops (F). 6. Install canopy (H) to mounting plate (C) and secure with collar
rings (I).
7. Determine desired overall length, and amount of chains (J) needed.
Shorten chain using chain pliers. (Keep extra chain)
8. Attach chains (J) to collar loops (F) and fixture loops (K) using quick
links (G). Secure quick links (G).
9. Thread fixture wire, ground wire through chain (J).
NOTE: When you reach the collar loop (F), ensure there is no tension
on the wires. Cut excess wires, being sure to leave enough to reach
the junction box.
10. Separate two sides of molded wire, and strip insulation on each 5/8″.
11. Loosen collar rings (I) and let canopy (H) slip down chains (J)
carefully.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 1
Alberto Large Linear Chandelier
Item # JN 5313
NOTICE:
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
B
Retain all packaging material until installation is complete and approved.
C
E
F
A
D
G
H
I J
12. Twist all fixture wires together. Slip through center hole of collar loop (F). NOTE: Untwist wires and separate to prepare for connection.
13. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
G
NOTE: It is imperative that the fixture is grounded.
K
14. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually
white) using wire nut (A).
15. Connect fixture hot wire (smooth with markings) to the supply hot
wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
Bulbs not included
16. Make sure all wire connections are tight, then carefully tuck into the junction box.
17. Install canopy (H) to mounting plate (C) and secure with collar
rings (I).
18. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
M
LI ST ED
US
