SL 5863 Linear Branched Chandelier
Product Information:
Linear Branched Chandelier
Item # SL 5863
Bulbs not included (Shade Sold Separately)
This light fixture should be installed in accordance with all
applicable, local installation codes, and by a person familiar with
the construction and operation of it, as well as the hazards
involved. Inspect item and contents carefully. If any damage or
defect is found, do not install. Retain all packaging material
until installation is complete and approved.
Care Instructions: Clean only with a soft dry cloth or feather
duster. Do Not use abrasive or chemical agents.
Product Usage Instructions:
- Carefully remove all parts from the box. Place on a clean, soft
surface. - Feed electrical wires through bottom rod (H) and connect to
fixture body (J). - Feed electrical wires through collar ring (F), canopy (E), and
top rod (G). Then connect top rod (G) to bottom rod (H). - Secure collar loop (C) to mounting plate (B) using pliers to
tighten locknut. - Install mounting plate (B) to the junction box and secure with
mounting screws (D). - Cut excess wires, being sure to leave enough to reach the
junction box. Separate wires, and strip insulation on each
5/8. - Wrap fixture ground wire (bare copper) around the green
grounding screw (see diagram 1). Tighten. Continue fixture ground
wire and connect to supply ground wire (usually green or bare
copper) using wire nut (A).
NOTE: It is imperative that the fixture is grounded. - Connect fixture neutral wire (ribbed) to the supply neutral
wire (usually white) using wire nut (A). - Connect fixture hot wire (smooth with markings) to the supply
hot wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral
connections. - Make sure all wire connections are tight, then carefully tuck
into the junction box. - Install canopy (E) to collar loop (C) and secure with collar
ring (F). - Place shades (K) on top of sockets (J) as shown in line
diagram.
NOTE: Shades are sold separately. - Install light bulbs into the sockets.
ASSEMBLY INSTRUCTIONS
A
B
Diagram 1
C D
E F
G
H
Bulbs not included K (Shade Sold Separately)
J
Linear Branched Chandelier
Item # SL 5863
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Measuring Tape
Wire Strippers
Chain Pliers Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Feed electrical wires through bottom rod (H) and connect to fixture
body (J). 3. Feed electrical wires through collar ring (F), canopy (E) and top
rod (G). Then connect top rod (G) to bottom rod (H). 4. Secure collar loop (C) to mounting plate (B) using pliers to tighten
locknut. 5. Install mounting plate (B) to the junction box and secure with
mounting screws (D). 6. Cut excess wires, being sure to leave enough to reach the junction
box. Separate wires, and strip insulation on each 5/8″. 7. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded. 8. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A). 9. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
A
B
Diagram 1
C D
E F
G
H
Bulbs not included K (Shade Sold Separately)
Linear Branched Chandelier
Item # SL 5863
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
10. Make sure all wire connections are tight, then carefully tuck into the junction box.
11. Install canopy (E) to collar loop (C) and secure with collar ring (F). 12. Place shades (K) on top of sockets (J) as shown in line diagram.
NOTE: Shades are sold separately. 13. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
J
M
LI ST ED
US
