CHC 5880 Large Two Tier Chandelierv
Product Information
The Darlana Large Two Tier Chandelier (Item # CHC 5880) is a
light fixture that adds elegance and style to any space. It
features a two-tier design and requires bulbs for operation (bulbs
not included). The chandelier should be installed in accordance
with all applicable local installation codes by a person familiar
with its construction and operation.
Important Notice
Inspect the item and its contents carefully before installation.
If any damage or defect is found, do not install the chandelier.
Retain all packaging material until installation is complete and
approved.
Tools Required (Not Included)
- Phillips Screwdriver
- Slip Joint Pliers
- Wire Strippers
- Slotted Screwdriver
- Measuring Tape
- Chain Pliers
- Wire Cutters
Product Usage Instructions
- Carefully remove all parts from the box and place them on a
clean, soft surface. - Install the mounting plate (B) to the junction box using the
provided mounting screws (C). - Secure the collar loop (D) to the mounting plate (B) by
tightening the locknut with pliers. - Attach the canopy (E) to the collar loop (D) and secure it with
the collar ring (F). - Determine the desired overall length and amount of chain (H)
needed. Use chain pliers to shorten the chain as necessary, while
keeping extra chain available. - Attach the chains (K) to the fixture loop (I) and top fixture
frame (L) using the provided hooks (J). - Attach the chain (H) to the collar loop (D) and fixture loop
(I) using the quick links (G). Secure the quick links. - Attach the chains (M) to the loop on the top fixture frame (L)
and loop on the bottom fixture frame (N) using the hooks (J). - Thread the fixture wire and ground wire through the chains (M
& K), fixture loop (I), and chain (H). When reaching the collar
loop (D), ensure there is no tension on the wires. Cut any excess
wires, leaving enough to reach the junction box. - Separate the two sides of the molded wire and strip insulation
on each side by 5/8 inch. - Loosen the collar ring (F) and carefully let the canopy (E)
slip down the chain (H). - Twist all fixture wires together and slip them through the
center hole of the collar loop (D). Untwist and separate the wires
to prepare for connection. - Wrap the fixture ground wire (bare copper) around the green
grounding screw as shown in diagram 1. Tighten it securely.
Continue by connecting the fixture ground wire to the supply ground
wire (usually green or bare copper) using a wire nut (A). It is
important to ensure proper grounding of the fixture. - Connect the fixture neutral wire (ribbed) to the supply neutral
wire (usually white) using a wire nut (A). - Connect the fixture hot wire (smooth with markings) to the
supply hot wire (usually black) using a wire nut (A). Take caution
not to reverse the hot and neutral connections. - Ensure all wire connections are tight and carefully tuck them
into the junction box. - Install the canopy (E) to the collar loop (D) and secure it
with the collar ring (F). - Install light bulbs into the sockets.
ASSEMBLY INSTRUCTIONS
Diagram 1
A B C D E F G
H
G I J K
Bulbs not included
L J M
N
Darlana Large Two Tier Chandelier
Item # CHC 5880
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slip Joint Pliers Wire Strippers
Slotted Screwdriver Measuring Tape
Chain Pliers Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Install mounting plate (B) to the junction box and secure with
mounting screws (C). 3. Secure collar loop (D) to mounting plate (B) using pliers to tighten
locknut. 4. Install canopy (E) to collar loop (D) and secure with collar ring (F). 5. Determine desired overall length, and amount of chain (H) needed.
Shorten chain using chain pliers. (Keep extra chain) 6. Attach chains (K) to fixture loop (I) and top fixture frame (L) using
hooks (J). 7. Attach chain (H) to collar loop (D) and fixture loop (I) using quick
links (G). Secure quick links (G). 8. Attach chains (M) to loop on top fixture frame (L) and loop on bottom
fixture frame (N) using hooks (J). 9. Thread fixture wire and ground wire through chains (M & K ), fixture
loop (I) and chain (H). NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 10. Separate two sides of molded wire, and strip insulation on each 5/8″. 11. Loosen collar ring (F) and let canopy (E) slip down chain (H) carefully.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 1
A B C D E F G
H
G I J K
Bulbs not included
L J M
N
Darlana Large Two Tier Chandelier
Item # CHC 5880
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
12. Twist all fixture wires together, and slip through center hole of collar loop (D). NOTE: Untwist wires and separate to prepare for connection.
13. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
14. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
15. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
16. Make sure all wire connections are tight, then carefully tuck into the junction box.
17. Install canopy (E) to collar loop (D) and secure with collar ring (F). 18. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
