CHC 1474 Gramercy Large Chandelier
Product Information
- Product Name: Gramercy Large Chandelier
- Item Number: CHC 1474
- Bulbs: Not included
- Installation Requirements: This light fixture should be
installed in accordance with all applicable, local installation
codes, and by a person familiar with the construction and operation
of it, as well as the hazards involved. - Inspection: Inspect item and contents carefully. If any damage
or defect is found, do not install. Retain all packaging material
until installation is complete and approved. - Tools Required (Not Included): Phillips Screwdriver, Slotted
Screwdriver, Slip Joint Pliers, Measuring Tape, Wire Strippers,
Chain Pliers, Wire Cutters - Care Instructions: Clean only with a soft dry cloth or feather
duster. Do not use abrasive or chemical agents.
Product Usage Instructions
- Remove all parts from the box and place them on a clean, soft
surface. - Remove collar loop (D) from chain (H) by removing quick link
(E). - Install mounting plate (B) to the junction box and secure it
with mounting screws (C). - Secure collar loop (D) to mounting plate (B) using pliers to
tighten the locknut. - Install canopy (F) to collar loop (D) and secure it with collar
ring (G). - Determine the desired overall length and amount of chain (H)
needed. Shorten the chain using chain pliers. Keep the extra
chain. - Thread rod (J) to the top of the fixture (K).
- Attach chain (H) to collar loop (D) and fixture loop (I) using
quick links (E). Secure the quick links (E). - Thread the fixture wire and ground wire through the chain (H).
When reaching the collar loop (D), ensure there is no tension on
the wires. Cut excess wires, leaving enough to reach the junction
box. - Separate the two sides of the molded wire and strip insulation
on each 5/8. - Loosen collar ring (G) and let canopy (F) slip down the chain
(H) carefully. - Twist all fixture wires together and slip them through the
center hole of collar loop (D). Untwist the wires and separate them
to prepare for connection. - Wrap the fixture ground wire (bare copper) around the green
grounding screw. Tighten it. Continue the fixture ground wire and
connect it to the supply ground wire using a wire nut (A). - Connect the fixture neutral wire (ribbed) to the supply neutral
wire using a wire nut (A). - Connect the fixture hot wire (smooth with markings) to the
supply hot wire using a wire nut (A). Do not reverse the hot and
neutral connections. - Ensure all wire connections are tight, then carefully tuck them
into the junction box. - Install canopy (F) to collar loop (D) and secure it with collar
ring (G). - Install light bulbs into the sockets.
ASSEMBLY INSTRUCTIONS
Diagram 1
A B C D E F G H E I
J
K
Bulbs not included
Gramercy Large Chandelier
Item # CHC 1474
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Measuring Tape
Wire Strippers
Chain Pliers Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove collar loop (D) from chain (H) by removing quick link (E). 3. Install mounting plate (B) to the junction box and secure with
mounting screws (C). 4. Secure collar loop (D) to mounting plate (B) using pliers to tighten
locknut. 5. Install canopy (F) to collar loop (D) and secure with collar ring (G). 6. Determine desired overall length, and amount of chain (H) needed.
Shorten chain using chain pliers. (Keep extra chain) 7. Thread rod (J) to the top of fixture (K). 8. Attach chain (H) to collar loop (D) and fixture loop (I) using quick
links (E). Secure quick links (E). 9. Thread fixture wire and ground wire through chain (H).
NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 10. Separate two sides of molded wire, and strip insulation on each 5/8″. 11. Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully. 12. Twist all fixture wires together. Slip through center hole of collar loop (D). NOTE: Untwist wires and separate to prepare for connection.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 1
A B C D E F G H E I
J
K
Bulbs not included
Gramercy Large Chandelier Item # CHC 1474
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
13. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
14. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
15. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
16. Make sure all wire connections are tight, then carefully tuck into the junction box.
17. Install canopy (F) to collar loop (D) and secure with collar ring (G). 18. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
