CHC 1140 Bernardo Medium Chandelier
Product Information:
Product Name: Bernardo Medium Chandelier
Item Number: CHC 1140
Included Parts: Mounting plate (B), collar loop
(D), chain (G), canopy (E), collar ring (F), fixture arms (M),
center plate (N), washers (O), lock nuts (P), jumper wire (ribbed),
fixture neutral wire (ribbed), wire nut (Q), jumper wire (smooth
with markings), fixture hot wire (smooth with markings), metal bowl
(S), threaded nipple (R), metal ring (T), rubber washers (U), glass
bowl (V), finial (W)
Additional Requirements: Phillips screwdriver,
slotted screwdriver, slip joint pliers, measuring tape, wire
strippers, chain pliers, wire cutters
Product Usage Instructions:
- Remove all parts from the box and place them on a clean
surface. - Detach collar loop (D) from chain (G) by removing quick link
(H). - Install the mounting plate (B) to the junction box using the
provided mounting screws (C). - Secure collar loop (D) to the mounting plate (B) by tightening
the locknut with pliers. - Attach the canopy (E) to the collar loop (D) and secure it with
the collar ring (F). - Determine the desired overall length and amount of chain (G)
needed. Use chain pliers to shorten the chain, keeping the extra
chain for future use. - Connect the chain (G) to the collar loop (D) and fixture loop
(I) using the quick links (H). Secure the quick links (H). - Attach the fixture arms (M) to the center plate (N) and secure
them with washers (O) and lock nuts (P). Ensure that the arms are
evenly spaced before final tightening. - Connect all neutral wires (ribbed) from three (3) of the
fixture arms (M) with the jumper wire (ribbed) and fixture neutral
wire (ribbed). Secure the connections with a wire nut (Q). Repeat
this step with the remaining three (3) wires on the opposite side
of the fixture. Refer to diagram 2. - Connect all hot wires (smooth with markings) from three (3) of
the fixture arms (M) with the jumper wire (smooth with markings)
and fixture hot wire (smooth with markings). Secure the connections
with a wire nut (Q). Repeat this step with the remaining three (3)
wires on the opposite side of the fixture. Refer to diagram 2. - Install the metal bowl (S) to the threaded nipple (R) and
secure it with the metal ring (T). - Attach rubber washers (U) to either side of the glass bowl (V),
then install it to the threaded nipple (R) and secure it with the
finial (W). - Thread the fixture wire and ground wire through the chain (G).
When reaching the collar loop (D), ensure there is no tension on
the wires. Cut any excess wires, leaving enough length to reach the
junction box.
Important Note: This light fixture should be
installed in accordance with all applicable local installation
codes and by a person familiar with its construction and operation,
as well as the associated hazards. Before installation, carefully
inspect the item and its contents. If any damage or defect is
found, do not proceed with the installation. Retain all packaging
material until the installation is complete and approved.
ASSEMBLY INSTRUCTIONS
Diagram 3
A B
C D
H E F
G
H I
J
N
O
QR
P
S T
U
V U
W
Fixture neutral wire
Fixture hot wire
Jumper neutral wire
Arm neutral wires
Jumper hot wire
Arm hot wires
Diagram 2
Bulbs not included K L
M Diagram 1
N O P
Bernardo Medium Chandelier
Item # CHC 1140
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Measuring Tape
Wire Strippers
Chain Pliers Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove collar loop (D) from chain (G) by removing quick link (H).
3. Install mounting plate (B) to the junction box and secure with
mounting screws (C).
4. Secure collar loop (D) to mounting plate (B) using pliers to tighten
locknut.
5. Install canopy (E) to collar loop (D) and secure with collar ring (F).
6. Determine desired overall length, and amount of chain (G) needed.
Shorten chain using chain pliers. (Keep extra chain)
7. Attach chain (G) to collar loop (D) and fixture loop (I) using quick
links (H). Secure quick links (H).
8. Install fixture arms (M) to center plate (N) and secure with
washers (O) and lock nuts (P). (See diagram 1)
NOTE: Check that the arms are spaced evenly before final tightening.
9. Connect all neutral wires (ribbed) from three (3) of the fixture arms (M)
with jumper wire (ribbed) and fixture neutral wire (ribbed), then secure
with wire nut (Q). Repeat with remaining three (3) wires on opposite
side of fixture. See diagram 2.
10. Connect all hot wires (smooth with markings) from three (3) of the
fixture arms (M) with jumper wire (smooth with markings) and fixture
hot wire (smooth with markings), then secure with wire nut (Q).
Repeat with remaining three (3) wires on opposite side of fixture.
See diagram 2.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 3
A B
C D
H E F
G
H I
J
N
O
QR
P
S T
U
V U
W
Fixture neutral wire
Fixture hot wire
Jumper neutral wire
Arm neutral wires
Jumper hot wire
Arm hot wires
Diagram 2
Bulbs not included K L
M Diagram 1
N O P
Bernardo Medium Chandelier
Item # CHC 1140
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
11. Install metal bowl (S) to threaded nipple (R) and secure with metal ring (T).
12. Attach rubber washers (U) to either side of glass bowl (V) and install to threaded nipple (R) and secure with finial (W).
13. Thread fixture wire and ground wire through chain (G). NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.
14. Separate two sides of molded wire, and strip insulation on each 5/8″. 15. Loosen collar ring (F) and let canopy (E) slip down chain (G) carefully. 16. Twist all fixture wires together. Slip through center hole of collar
loop (D). NOTE: Untwist wires and separate to prepare for connection. 17. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 3). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded. 18. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A). 19. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections. 20. Make sure all wire connections are tight, then carefully tuck into the junction box.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 3
A B
C D
H E F
G
H I
J
N
O
QR
P
S T
U
V U
W
Fixture neutral wire
Fixture hot wire
Jumper neutral wire
Arm neutral wires
Jumper hot wire
Arm hot wires
Diagram 2
Bulbs not included K L
M Diagram 1
N O P
Bernardo Medium Chandelier
Item # CHC 1140
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
21. Install canopy (E) to collar loop (D) and secure with collar ring (F). 22. Place discs (L) and tubes (K) onto arms (M). 23. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
