JN 5112 Talia Large Chandelier
Product Information: Product Name: Talia Large Chandelier
Item Number: JN 5112 Included Components: Mounting plate (A),
collar loop (B), chain (F), canopy (D), collar ring (E), quick
links (I), fixture loop (G), chain (J), fixture ground wire, supply
ground wire, fixture neutral wire, supply neutral wire, fixture hot
wire, supply hot wire, light bulbs (not included), glass balls
Product Usage Instructions: 1. Carefully remove all parts
from the box and place them on a clean, soft surface. 2. Unscrew
the quick link (I) to remove the collar loop (B) from the chain
(F). 3. Install the mounting plate (A) to the junction box using
the provided mounting screws (C). 4. Secure the collar loop (B) to
the mounting plate (A) by tightening the locknut with pliers. 5.
Attach the canopy (D) to the collar loop (B) and secure it with the
collar ring (E). 6. Determine the desired overall length and amount
of chain (F) needed. Use chain pliers to shorten the chain if
necessary. Keep any extra chain for future use. 7. Attach the chain
(F) to the collar loop (B) and fixture loop (G) using quick links
(I). Make sure to secure the quick links. 8. Thread the fixture
wire and ground wire through the chain (J) and chain (F). When you
reach the collar loop (B), ensure there is no tension on the wires.
Cut any excess wires, leaving about 12 inches to reach the junction
box. 9. Separate the two sides of the molded wire and strip
insulation on each side about 5/8 inch. 10. Loosen the collar ring
(E) and carefully let the canopy (D) slip down the chain (F). 11.
Twist all fixture wires together and slip them through the center
hole of the collar loop (B). Untwist the wires and separate them to
prepare for connection. 12. Wrap the fixture ground wire (bare
copper) around the green grounding screw and tighten it. Continue
the fixture ground wire and connect it to the supply ground wire
using a wire nut (H). Ensure proper grounding of the fixture. 13.
Connect the fixture neutral wire (ribbed) to the supply neutral
wire (usually white) using a wire nut (H). 14. Connect the fixture
hot wire (smooth with markings) to the supply hot wire (usually
black) using a wire nut (H). Be cautious not to reverse the hot and
neutral connections. 15. Ensure all wire connections are tight,
then carefully tuck them into the junction box. 16. Install the
canopy (D) to the collar loop (B) and secure it with the collar
ring (E). 17. Insert the light bulbs into the sockets. 18. Attach
the chains (J) to the hooks on the fixture body (K) using quick
links (I). Secure the quick links. 19. Install the glass balls
starting from the bottom layer and follow the provided diagram for
proper arrangement. Note: Please refer to Diagram 1 in the user
manual for visual reference during assembly. Make sure to follow
all applicable local installation codes and seek assistance from a
person familiar with the construction and operation of the
chandelier if needed. Inspect the item and contents carefully
before installation, and do not proceed if any damage or defect is
found. Retain all packaging material until installation is complete
and approved.
ASSEMBLY INSTRUCTIONS
Diagram 1
H A C B D E I
F
I G J
I
Bulbs not included
K
Talia Large Chandelier
Item #JN 5112
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Measuring Tape
Wire Strippers
Chain Pliers Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove collar loop (B) from chain (F) by unscrewing quick link (I). 3. Install mounting plate (A) to junction box and secure with mounting
screws (C). 4. Secure collar loop (B) to mounting plate (A) using pliers to tighten
locknut. 5. Install canopy (D) to collar loop (B) and secure with collar ring (E). 6. Determine desired overall length, and amount of chain (F) needed.
Shorten chain using chain pliers. (Keep extra chain) 7. Attach chain (F) to collar loop (B) and fixture loop (G) using quick
links (I). Secure quick links (I). 8.. Thread fixture wire and ground wire through chain (J) and chain (F).
NOTE: When you reach the collar loop (B), ensure there is no tension on the wires. Cut excess wires, being sure to leave about 12″ to reach the junction box. 9. Separate two sides of molded wire, and strip insulation on each 5/8″. 10. Loosen collar ring (E) and let canopy (D) slip down chain (F) carefully. 11. Twist all fixture wires together. Slip through center hole of collar loop (B). NOTE: Untwist wires and separate to prepare for connection.
M
L IST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 1
H A C B D E I
F
I G J
I
Bulbs not included
K
Talia Large Chandelier Item #JN 5112
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
12. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (H). NOTE: It is imperative that the fixture is grounded.
13. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (H).
14. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (H). CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the junction box.
16. Install canopy (D) to collar loop (B) and secure with collar ring (E). 17. Insert light bulbs into the sockets. 18. Attach chains (J) to hooks on fixture body (K) using quick links (I).
Secure quick links (I). 19. Install glass balls starting from bottom (layer 1
and working your
way to the top (layer 8) as shown in figures L1-L8.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents..
M
L IST ED
US
ASSEMBLY INSTRUCTIONS
8 6
4 2
7 5 3
1 S
Talia Large Chandelier
Item #JN 5112
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
163mm L (25pcs + 2pcs spare parts)
110mm S (13pcs + 2pcs spare parts)
137mm M (30pcs + 2pcs spare parts)
M
L IST ED
US
ASSEMBLY INSTRUCTIONS
L1
L2 M
M M
Talia Large Chandelier
Item #JN 5112
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
M
M
S
L L
L3 L
L
S
L
S
L4 S
S S
L L
L L
S S
S S
M
L IST ED
US
ASSEMBLY INSTRUCTIONS
L5 M
M
M
L6
L L
L
Talia Large Chandelier
Item #JN 5112
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
L
M
M
L
M M
M L7
M
M M
M M
L L
L L
M
L
S
M
M
L
M
M
S
L8
L
M
M
M
L
M M
S
L M
M
L L
M
L IST ED
US
