AH 5010 Myrna Chandelier
Product Information:
Product Name: Myrna Chandelier
Item Number: AH 5010
Product Description: The Myrna Chandelier is a stylish and
elegant lighting fixture that adds a touch of sophistication to any
space. It features a top column, fixture body, threaded nipple,
chain, canopy, lock collar, and shade. The chandelier requires
bulbs (not included) for illumination.
Assembly Requirements: The assembly of the Myrna Chandelier
requires a 1/4 IPS threaded nipple pipe, which is not provided with
the product.
Product Usage Instructions:
- 1. Carefully remove all parts from the box.
- 2. Thread the top column (I) to the fixture body (J).
- 3. Install a 1/4 threaded nipple in your outlet box and attach
the threaded nipple (B) to the outlet box. - 4. Unscrew the threaded collar on the chain end link (G) and
attach it to the top ring (H). Close the threaded collar to secure
the fixture body. - 5. Pass the canopy (D) and lock collar (E) through the chain
(F). - 6. Adjust the length of the chain (F) using a pair of chain
pliers according to the desired fixture dimension. - 7. Unscrew the threaded collar on the other chain end link and
raise the canopy (D) to the ceiling loop (C). Secure it with the
lock collar (E). - 8. Insert bulbs (not included) into the sockets.
- 9. Clip the shade (K) onto the bulb.
- 10. Connect the fixture’s Hot wire (smooth edge, markings) with
the hot wire from the outlet box using a wire nut (A). Ensure that
the hot and neutral connections are not reversed to maintain
safety. - 11. Tuck the wire connections neatly into the outlet box to
secure them. - 12. Installation is complete. Turn on power at the fuse or
circuit breaker.
Note: This light fixture should be installed in
accordance with all applicable local installation codes by a person
familiar with its construction and operation. Carefully inspect the
item and its contents for any damage or defects before
installation. Retain all packaging material until installation is
complete and approved.
Care Instructions:
Clean the Myrna Chandelier only with a soft dry cloth or feather
duster. Do not use abrasive or chemical agents.
ASSEMBLY INSTRUCTIONS
Ceiling Box Cable lock nut Safety cable
TO assemble safety cables: 1.Join fixture safety cables with safety cable from ceiling. 2.Wrap both safety cable around the cable lock nut. 3.Insert screws into both holes on cable lock nut,secure screws with screwdriver. 4.Push the cable lock nut into outlet box.
1/4 IPS threaded nipple pipe (Not provided)
Myrna Chandelier
Item # AH 5010
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
1. Carefully remove all parts from the box. 2. Thread the top column (I) to the fixture body (J). 3. A 1/4″ threaded nipple must be installed in your outlet box. Then install
the threaded nipple (B) into the outlet box. 4. Unscrew the threaded collar on the chain end link (G) and attach it to
the top ring (H). Close the threaded collar to secure the fixture body. 5. Let canopy (D) and lock collar (E) go through the chain (F). 6. With the fixture dimension as a guide, shorten the chain (F) as needed
using a pair of chain pliers. 7. Unscrew the threaded collar on the other chain end link, raise the
fixture then attach chain end link to the ceiling loop (C). Close the threaded collar to secure. 8. Unwrap the wiring from the top of the fixture body. Weave the power supply cord and the ground wire through the chain (F). 9. When you reach the canopy and ceiling loop, measure the wires then cut. Be certain to leave enough to connect inside of the outlet box. 10. Strip the insulation back on the two power supply wires about 5/8″. 11. Twist the power supply and ground wire together and push through the center hole of the ceiling loop (C). 12. Connect the fixture ground (bare) wire with the ground wire from the outlet box using wire nut (A). If your house does not have ground wire, then attach this wire to the green grounding screw inside of the outlet box. IT IS IMPERATIVE THAT THIS FIXTURE BE GROUNDED. 13. Connect the fixture Neutral wire (ribbed, no markings) with the neutral wire from the outlet box using wire nut (A).
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Ceiling Box Cable lock nut Safety cable
TO assemble safety cables: 1.Join fixture safety cables with safety cable from ceiling. 2.Wrap both safety cable around the cable lock nut. 3.Insert screws into both holes on cable lock nut,secure screws with screwdriver. 4.Push the cable lock nut into outlet box.
1/4 IPS threaded nipple pipe (Not provided)
Myrna Chandelier Item # AH 5010
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
14. Connect the fixture Hot (smooth edge,markings) wire with the hot wire from the outlet box using wire nut (A). DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
15. Tuck these wire connections neatly into the outlet box to secure. 16. Put canopy (D) to ceiling loop (C), and secure with lock collar (E). 17. Insert bulbs (not included) into the sockets. 18. Clip the shade (K) onto the bulb. 19. Installation is complete, turn on power at fuse or circuit breaker.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
