JN5333 Chalmette 38 Inch Layered Pendant
Product Information:
Product Name: Chalmette 38 Layered Pendant
Item Number: JN5333
Bulbs: Not included
Assembly Instructions: Diagram 1
Notice: This light fixture should be installed in accordance
with all applicable, local installation codes, and by a person
familiar with the construction and operation of it, as well as the
hazards involved. Inspect item and contents carefully. If any
damage or defect is found, do not install. Retain all packaging
material until installation is complete and approved.
Tools Required (Not Included):
- Phillips Screwdriver
- Slotted Screwdriver
- Slip Joint Pliers
- Measuring Tape
- Wire Strippers
- Chain Pliers
- Wire Cutters
Product Usage Instructions:
- Carefully remove all parts from the box and place them on a
clean, soft surface. - It is recommended to install a 1/4 IPS threaded pipe, secured
to a structural member of the building. - Loosen the cable lock and install it to the end of the safety
cable. - Run the safety cable through the junction box and around a
structural member of the building. - Insert the cable through the cable lock and tighten the ends
with a screwdriver to secure it. Refer to Diagram 1 for more
details. - Connect the fixture ground wire (bare copper) to the supply
ground wire (usually green or bare copper) using a wire nut (A). It
is important to ground the fixture. - Connect the fixture neutral wire (ribbed) to the supply neutral
wire (usually white) using a wire nut (A). - Connect the fixture hot wire (smooth with markings) to the
supply hot wire (usually black) using a wire nut (A). Be cautious
not to reverse the hot and neutral connections. - Ensure all wire connections are tight, then carefully tuck them
into the junction box. - Install the canopy (D) to the collar loop (C) and secure it
with the collar ring (E). - Install the light bulbs into the sockets.
Care Instructions: Clean the fixture only with
a soft dry cloth or feather duster. Do not use abrasive or chemical
agents.
ASSEMBLY INSTRUCTIONS
Diagram 1
1/4 IPS Pipe (Not provided) A B C G D E F G I
Bulbs not included
Chalmette 38″ Layered Pendant
Item # JN5333
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Measuring Tape
Wire Strippers
Chain Pliers Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. It is recommended to install a 1/4 IPS threaded pipe, secured to a
structural member of the building (not included). Then install hex nut and threaded nipple (B) into receiver and tighten with the wrench. NOTE: Item must be supported independent of the junction box due to weight. 3. Remove collar loop (C) from chain (F) and secure to threaded receiver attached to structural member by tightening locknut. 4. Install canopy (D) to collar loop (C) and secure with collar ring (E). 5. Determine desired overall length, and amount of chain (F) needed. Shorten chain using chain pliers. (Keep extra chain) 6. Attach chain (F) to collar loop (C) and fixture loop (I) using quick links (G). Secure quick links (G). 7. Thread fixture wire and ground wire through chain (F). NOTE: When you reach the collar loop (C), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 8. Separate two sides of molded wire, and strip insulation on each 5/8″. 9. Loosen collar ring (E) and let canopy (D) slip down chain (F) carefully. 10. Twist all fixture wires together, and slip through center hole of collar loop (C). NOTE: Untwist wires and separate to prepare for connection.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 1
1/4 IPS Pipe (Not provided) A B C G D E F G I
Bulbs not included
Chalmette 38″ Layered Pendant
Item # JN5333
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
11. Loosen cable lock and install to end of safety cable. Run safety cable through junction box and around structural member of building. Insert cable through cable lock and tighten the ends with a screwdriver to secure. (See diagram 1)
12. Connect fixture ground wire (bare copper) to the supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
13. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
14. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the junction box.
16. Install canopy (D) to collar loop (C) and secure with collar ring (E). 17. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
