Eglo 20557501 40 Degree Canopy Instruction Manual

20557501 40 Degree Canopy

Product Information

Product Usage Instructions

1. The fixing point for your ceiling fan must be of sound
   construction, capable of supporting a load of 35Kg, or 4 times the
   weight of the fan, whichever is less.
2. Avoid installing the ceiling fan too close to the ceiling or
   any obstructions, as it can reduce the amount of air movement.
   Leave a clearance of at least 2.1m between the bottom of the blades
   and the floor, and a minimum of 3.0m between ceiling fans.
3. Ensure that the fan and the hanging bracket are properly
   earthed.
4. Use the appropriate fixing equipment for installation on timber
   ceilings or other materials. Fixing screws may need to be purchased
   separately.
5. Before installing the ceiling fan, remove the hanger ball from
   your existing downrod assembly by removing the screw, lowering the
   hanger ball, and removing the pin. Then slide the hanger ball off
   the downrod.
6. Select the correct size hanger ball insert based on the
   diameter of the downrod on the fan being installed.

Distributed by: Reduction Revolution Pty Ltd
www.reductionrevolution.com.au

‘

d capable of supporting a load of 35Kg,or 4 timesth

r,,aged,an

e

1.

Thefixing point for your ceilingfan must be of sound construction,unda

. .

.

i h an . .

weight of the fi!Jnplusthe method of attachment, whichever is greater· h fan bladesto come into.contact w t YobJectOr surface.

2.

Careneedsto be taken to ensurethe installation location doesnota11°Wt e d the nearest wall or obJect. Reduced clearancesto Wallsor

There must· be a minimum of 60cmclearancebetween the bladetiP(end)caanuseyour fan to de-stab·I1is· e.

.

..

ceiling can not only reducethe amount of air your fan can move bUtalso d the bottom of the blades. The ,nstallation should allowfor

, f}ooran

3. The installation should alsoallow for a clearanceof 2.lm betweent,he . ;

.

·

a minimum of 3.0m between ceiling fans.

4. Thefan and the ha~gingbracket must be earthed.

.
..-,.:::.
c >

@x1

@x1

@x2

©

0

A:

Mounting Bracket

B:

Canopy

C:

Hanger ball

D:

Hanger Ball Insert – 26.5mm downrods

E:

Hanger Ball Insert- 21.0mm downrods

F:

Hanger Ball Pin

G:

ReceiverShelf ,

. . H:

wood Screws & Washers

Important: When·mounted on anglei:J/sloped ceilings, the h’ttin.~ert,racketmust be installed so that the opening.is facing acrossthe direction of ceiling pitch. This angle ceiling bracket mlfst only be 4led on a maximum 40 degree sloped ceiling pitch, and must have a minimum of 60cm clearance from the lower side of.the ceiling t0t:he edge of the’fan blade. It would be expected that in many installations, and extension downrod will nee’d to be purchased separately.

:’1ie1#:ingserews,,included are designed for use with t’lmbej~ilimgj'(!)fs”tsf,ar afl other materials, t:he:.appropriate fixing eeb’ tmbepur9hased separately.

.

if·

,· .

I .

. –

‘ 0
®
x2
·
min. 30mm
.& ._I

. – ,……,,
· .:,..~··
, .:’.·.~…·.-. ‘
·

(G2. 0-

0

‘

Note: Remove the hanger ball from your existing downrod assemblyby removing the screw, lowering the hanger ball, and removing the pin, before sliding the hanger ball off the downrod.
·

I
(
O , Important: Select the correct size hanger ball insert Ci)or
according to the diameter of the down rod on the fan being installed .

‘
‘

0

‘

4.

· 0

-1—-Downrod (Not lndued)

·
40 Deg. Canopy Ceiling Fan Accessory

2 J

Distributed by: Reduction Revolution Pty Ltd
www.reductionrevolution.com.au

References

• Domain parked by OnlyDomains
• Reduction Revolution - Energy Efficiency Made Easy