MF 5025 Extra Large Hanging Shade
Product Information:
Product Name: Linley Extra Large Hanging Shade
Item Number: MF 5025
Product Description: The Linley Extra Large Hanging Shade is a
light fixture that adds a stylish touch to any room. It requires
bulbs for operation, which are not included in the package. The
fixture should be installed in accordance with all applicable local
installation codes and by a person familiar with its construction
and operation. It is important to inspect the item and contents
carefully before installation, and if any damage or defect is
found, do not install. Retain all packaging material until
installation is complete and approved.
Product Usage Instructions:
- Carefully remove all parts from the box and place them on a
clean, soft surface. - Remove collar loop (C) from chain (H) by removing quick link
(E). - Install mounting plate (B) to the junction box and secure it
with mounting screws (D). - Secure collar loop (C) to mounting plate (B) using pliers to
tighten the locknut. - Install canopy (F) to collar loop (C) and secure it with collar
ring (G). - Determine the desired overall length and amount of chain (H)
needed. Shorten the chain using chain pliers. Keep the extra
chain. - Attach chain (H) to collar loop (C) and fixture loop (I) using
quick links (E). Secure the quick links. - Thread the fixture wire and ground wire through the chain (H).
When reaching the collar loop (C), ensure there is no tension on
the wires. Cut excess wires, leaving enough to reach the junction
box. - Separate the two sides of the molded wire and strip insulation
on each 5/8 inch. - Loosen collar ring (G) and let the canopy (F) slip down the
chain (H) carefully. - Twist all fixture wires together and slip them through the
center hole of collar loop (C). Untwist and separate the wires to
prepare for connection. - Wrap fixture ground wire (bare copper) around the green
grounding screw. Tighten it. Continue the fixture ground wire and
connect it to the supply ground wire (usually green or bare copper)
using a wire nut (A). It is imperative that the fixture is
grounded. - Connect fixture neutral wire (ribbed) to the supply neutral
wire (usually white) using a wire nut (A). - Connect fixture hot wire (smooth with markings) to the supply
hot wire (usually black) using a wire nut (A). Do not reverse the
hot and neutral connections. - Ensure all wire connections are tight, then carefully tuck them
into the junction box. - Install canopy (F) to collar loop (C) and secure it with collar
ring (G). - Install light bulbs into the sockets.
Care Instructions:
Clean the Linley Extra Large Hanging Shade only with a soft dry
cloth or feather duster. Do not use abrasive or chemical
agents.
UNPACKING NOTICE: This section is missing from
the provided text. Please provide the necessary information if
available.
ASSEMBLY INSTRUCTIONS
Diagram 1
A B C D E F G H E I
Bulbs not included
Linley Extra Large Hanging Shade
Item # MF 5025
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Measuring Tape
Wire Strippers
Chain Pliers Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove collar loop (C) from chain (H) by removing quick link (E). 3. Install mounting plate (B) to the junction box and secure with
mounting screws (D). 4. Secure collar loop (C) to mounting plate (B) using pliers to tighten
locknut. 5. Install canopy (F) to collar loop (C) and secure with collar ring (G). 6. Determine desired overall length, and amount of chain (H) needed.
Shorten chain using chain pliers. (Keep extra chain) 7. Attach chain (H) to collar loop (C) and fixture loop (I) using quick
links (E). Secure quick links (E). 8. Thread fixture wire and ground wire through chain (H).
NOTE: When you reach the collar loop (C), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 9. Separate two sides of molded wire, and strip insulation on each 5/8″. 10. Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully. 11. Twist all fixture wires together. Slip through center hole of collar loop (C). NOTE: Untwist wires and separate to prepare for connection.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 1
A B C D E F G H E I
Bulbs not included
Linley Extra Large Hanging Shade Item # MF 5025
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
12. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
13. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
14. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the junction box.
16. Install canopy (F) to collar loop (C) and secure with collar ring (G). 17. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
UNPACKING NOTICE
Linley Extra Large Hanging Shade Item # MF 5025
NOTICE: Please follow instructions below to avoid possible damages caused by improper removal. 1. Open box and remove top layer of packaging. 2. Evenly lift metal frame in areas indicated by arrows (see diagram) until
clear of packaging. Place on clean, soft surface. NOTE: Remove slowly to avoid damages. 3. Carefully cut off cable ties (see diagram 2) , then evenly lift shade in areas indicated by arrows (see drawing) until clear of metal frame. Place on clean, soft surface. NOTE: Remove slowly to avoid damages.
Diagram 2
