MU2003 Singel Monitor Wall Mount
Product Information
The Single Monitor Wall Mount is designed to securely mount a
monitor on the wall. It is compatible with monitors that have a
VESA mounting pattern of 75x75mm or 100x100mm. The mount can
support monitors weighing between 2.2 to 17.6 lbs (1 to 8 kg). The
product is intended for use with wood studs or concrete walls.
Package Contents
- C (x1) Bolt
- D (x3) Decorative Cover
- A (x1) Arm
- B (x1) VESA Plate
- E (x1) 6mm Allen Key
- M-A (x4) M4x12mm
- M-B (x4) M4x25mm
- M-C (x4) Spacer H10mm
- W-A (x3) Lag Bolt M6x55mm
- W-B (x3) Anchor 9.6x43mm
- W-C (x3) Washer
Installation Tools (Not Included)
- Wood Stud Installation: Stud Awl, Wood Drill, Hammer, Finder,
Level, Pencil, Drill Socket Screwdriver, Wrench - Concrete Installation: Concrete Drill, Hammer, Finder, Level,
Pencil, Drill Socket Screwdriver, Wrench
Product Usage Instructions
Warning:
If you have any confusion or are not quite sure about the
installation, please do not hesitate to ask for our help. Before
assembly, please check and make sure all necessary accessories are
included and undamaged. Improper installation, such as using the
product for monitors over its load capacity or for any purpose not
explicitly specified, may cause damage or serious injury. We would
not be liable for any damage or injury caused by improper mounting
or inappropriate use. DO NOT install into drywall alone.
The kit contains small items that could be choking hazards if
swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS
OLD. ADULT SUPERVISION IS REQUIRED.
Assembly Steps:
NOTE: Not all hardware included will be used.
Step 1: Attach Arm to Wall
OPTION A: Wood Stud Installation
Minimum distance from the edge of the stud should be 102mm (4
inches) horizontally and 51mm (2 inches) vertically.
Singel Monitor Wall Mount
Instruction Manual
75x75mm 100x100mm
2.2~17.6 lbs 1~8 kg
If you have any questions, please contact our customer service.
80002-MA02-112W-US2.0
WARNING!
If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use. DO NOT install into drywall alone.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
C (x1) Bolt
D (x3) Decorative Cover
A (x1) Arm
B (x1) VESA Plate
E (x1) 6mm Allen Key
M-A (x4) M4x12mm
M-B (x4) M4x25mm
M-C (x4) Spacer H10mm
W-A (x3) Lag Bolt M6x55mm
W-B (x3) Anchor 9.6x43mm
Installation Tools (Not Included)
Wood Stud Installation Concrete Installation
W-C (x3) Washer
NOTE: Not all hardware included will be used.
Stud Awl Wood Drill Concrete Drill Hammer
Finder
ø3/16″(ø4.5mm) ø3/8″(ø10mm)
Level
Pencil
Drill Socket Screwdriver Wrench
01
WARNING
ASSEMBLY STEPS
DO NOT install into drywall alone.
STEP 1: Attach Arm to Wall
OPTION A: Wood Stud Installation
Min. 102mm (4″) Min. 51mm (2″) <16mm (5/8″)
Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder.
A
Position the Arm (A) at your desired height and line up the holes with your stud center line. Level the Arm (A) and mark the pilot hole locations.
55mm (2.2″)
ø 4.5mm (ø 3/16″)
Drill pilot holes using a ø3/16″. (ø4.5 mm) diameter drill bit.
W-C W-A
Caution:
Do not use anchor in drywall or wood
A
Install Arm (A) using lag bolts (W-A) and washers (W-C). Tighten the lag bolts until they are pulled firmly against the Arm (A).
02
STEP 1: (Continued) OPTION B: Solid Concrete Wall Installation
Min. 8″(203mm)
A
Position the Arm (A) at your desired height, level the Arm (A) and mark the pilot hole locations.
60mm (2.4″)
ø10mm (ø 3/8″)
60mm (2.4 )
Drill pilot holes using a ø3/8″. (ø10 mm) diameter drill bit.
W-C
W-B
W-A
A
Install Arm (A) using lag bolts (W-A), anchors (W-B) and washers (W-C). Tighten the lag bolts until they are pulled firmly against the Arm (A).
03
STEP 2: Attach Decorative Cover
Attach Decorative Covers (D) to Lag Bolts (W-A).
W-A
D
04
STEP 3: Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (B) to the back of monitor and secure it by using a 6 mm Allen Key (E) to tighten screws (M-A).
Do not tighten the screws excessively or your monitor might be damaged.
B
Monitor
Monitor Monitor
E M-A
OPTION B: Curved Back Monitor
Attach the VESA plate (B) to the back of monitor and secure it by using a 6 mm Allen Key (E) to tighten screws (M-B) along with spacers (M-C).
Do not tighten the screws excessively or your monitor might be damaged.
B
05
monitor
monitor monitor
E M-B
M-C
STEP 4: Hang Monitor
Slide the monitor onto the head of swivel arm, install the security bolt (C). Make sure the security bolt is installed before you rotate the monitor.
C
Important Notice: The gas spring is pre-set to minimum tension. Once the monitor is hanged on, hold the monitor with both hands and DO NOT let go suddenly or immediately. Instead, leave the monitor in a slow & gentle way while observing whether the arms will fall down wildly.
Guideline to adjust monitor tilting angle.
Problem: If monitor face down
E
06
Solution: 1. Loosen the tilting bolt.
2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
3. Retighten the tilting bolt to fix the intended angle.
STEP 5: Adjust Tension
For intended functioning of the mount, you may need to adjust the tension of Arm (A) in accordancewith your monitor weight by 6 mm Allen Key (E).
E
CAUTION
Note1:
Be sure to keep the arm in a horizontal position during adjustment. Or else it would be difficult to adjust the mount or damage the mount.
Situation 1: Arm falls down Upper Arm with monitor falls down and fails to stay where intended. Solution: Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.
Situation 2: Arm rises up Upper Arm with monitor rises up and fails to stay where intended.
Solution: Turn the inside screw clockwise(“-“direction) to decrease gas spring tension until the arm can stay as intended.
Note2:
For how many circles the screw should be turned, please refer to the table below.
Monitor Weight
2kg 3kg 4kg 5kg 6kg 7kg 8kg
Circles (AT LEAST) 1
2
4
6
8
9
12
07
STEP 65: C(aCbolnetMinauneadg) ement
Remove bottom plastic covers from gas spring arm as shown in diagram.
Run cables from monitor through bottom of gas spring arm. Reattach plastic covers as shown in diagram.
08
Adjust as Desired
Adjust monitor position and rotation.
Tilt Swivel Rotation Height
Swivel
±90°
Swivel
±135°
Swivel
±90°
360°
Rotation
+90°
Tilt
-45°
Height
max280mm
Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.
09
Product Dimensions
±135°
210mm-262mm 8.2″-10.3″
±90°
53mm /2.1″
±90°
160mm /6.3″
31mm /1.2″
75mm/2.9″ 100mm/3.9″ 114mm/4.5″
360°
75mm/2.9″ 100mm/3.9″ 114mm/4.5″
+90° -45°
280mm/11″
66mm /2.6″
170mm/6.7”
10
CAUTION AND MAINTENANCE:
· Never allow children to climb, stand, hang, or play on any part of monitor or stand. · This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury. · Check that the bracket is secure and safe to use at regular intervals
(at least every three months).
