PRDCRX783MB Widespread Double-Handle Waterfall Spout Bathroom Faucet
Product Information
The product is a widespread faucet, designed for installation in
sinks. It comes with detailed installation instructions to guide
users through the process. The faucet is made up of a spout, valve
stems, and a T-connector. It also includes braided water lines for
connecting the valve stems to the faucet body.
Product Usage Instructions
- Before beginning the installation, it is recommended to consult
a professional if you are unfamiliar with installing plumbing
fixtures. Also, make sure to observe all local plumbing and
building codes. - Gather all the required materials for the installation,
including plumbers tape, thread sealant, a Phillips screwdriver, an
adjustable wrench, a small bucket, and a basin wrench. - Ensure that the water supply below your sink is completely shut
off by turning the shutoff valves all the way to the right. Place a
small bucket below your workspace to catch any water that may drip
during the installation process. - Remove the old faucet completely and make any necessary repairs
or modifications to the water supply. - Slide the rubber washer back onto the spout and secure it using
the lock nut. Hand tighten the lock nut and then use a basin wrench
to finish tightening. - From under the counter, slide the rubber washer back onto the
valve stem followed by the metal washer. Secure it to the counter
by hand-tightening the lock nut. Finish securing by tightening the
screws on the lock nut using a Phillips screwdriver. - Repeat steps 5 and 6 for installing the hot valve stem into the
left faucet hole. - Use the provided braided water lines to connect the valve stems
to the faucet body’s T-connector. Use an adjustable wrench to
tighten, but be careful not to overtighten. Apply thread sealant or
plumber’s tape to each threaded connection before attaching. - Attach the valve stems to the main water supply. Use an
adjustable wrench to tighten, but be careful not to overtighten.
Apply thread sealant or plumber’s tape to each threaded connection.
Ensure that you are connecting the hot and cold lines
accordingly. - Once installation is complete, turn the main water supply back
on. Check for any leaks underneath. - Proceed to sink drain installation. Once the drain is
installed, turn the faucet on for approximately 60 seconds. Check
for any leaks. Test both hot and cold water to ensure they are
running properly.
WIDESPREAD FAUCET INSTALLATION
WIDESPREAD FAUCET INSTALLATION
BEFORE YOU BEGIN
We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures.
Observe all local plumbing and building codes.
INSTALLATION
1. Ensure that the water supply below your sink is completely shut o ffby turning the shuto ffvalves all the way to the right.
Tip: Place a small bucket below your workspace to catch any water that may drip during the installation process.
3. From below slide the rubber washer back onto the spout and secure using the lock nut. Hand tighten the lock nut, then use a basin wrench to finish tightening.
5. From under the counter, slide the rubber washer back onto the valve stem followed by the metal washer. Secure to the counter by hand- tightening the lock nut. Finish securing by tightening the screws on the lock nut using a Phillip’s screwdriver.
GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation.
For these instructions, it is assumed that the old faucet has been completely removed and any necessary repairs or modifications to the water supply have been completed.
TOOLS AND MATERIALS:
Plumbers Tape
Thread Sealant
Phillips Screwdriver
Adjustable Wrench
Small Bucket
Basin Wrench
2. Remove the T-connector, lock nut, and rubber washer from the spout body. Set the spout into the center faucet hole.
4. Remove the lock nut, metal washer, and rubber waasher from the valve stem labeled `cold.’ Insert the stem into the faucet hole on the right.
6. Repeat steps 4 and 5 for installing the `hot’ valve stem into the left faucet hole.
Widespread Faucet Installation Instructions 1
Widespread Faucet Installation Instructions 2
WIDESPREAD FAUCET INSTALLATION
7. Use the provided braided water lines to connect the valve stems to the faucet body’s T-connector. Use an adjustable wrench to tighten, but be careful not to overtighten. Apply thread sealant or plumber’s tape to each threaded connection before attaching.
9. Once installation is complete, turn the main water supply back on. Check for any leaks underneath.
8. Attach the valve stems to the main water supply. Use an adjustable wrench to tighten, but be careful not to overtighten. Apply thread sealant or plumber’s tape to each threaded connection. Ensure that you are connecting the hot and cold lines accordingly.
10. Proceed to sink drain installation. Once the drain is installed, turn the faucet on for approximately 60 seconds. Check for any leaks. Test both hot and cold water to ensure they are running properly.
Widespread Faucet Installation Instructions 3
