BPD74232 Pendant LED Fixture
Product Information: Fixture BPD74232
The Fixture BPD74232 is a lighting fixture that can switch
between three color temperatures (3000k-3500k-4000k) using a switch
in the canopy (Fig.4). The fixture comes with a Cloud Crystal
RPL-GLA-74232 that needs to be mounted against a spring sheet
inside the fixture. The fixture has a UL Approval for a maximum of
200 pounds and requires a junction box, mounting screws, wood
screws, and plastic anchors for installation.
Fig. 1: Mounting the Crystal and Fixture
1. Shut off power at the circuit breaker and remove the existing
fixture, including the crossbar.
2. Unpack the new fixture carefully and lay out all parts on a
clear area.
3. Install the Cloud crystal against the spring sheet from the
inside of the fixture, so that the two convex points of the crystal
align with the two holes of the fixture.
4. Remove the mounting screw (B) from the fixture.
5. The lamp can switch between three color temperatures
(3000k-3500k-4000k), which can be adjusted to your preference with
the switch in the canopy (Fig.4).
6. Drill holes in the wall aligned with the keyholes located in the
mounting backplate, insert the plastic anchor (D).
7. Secure the mounting plate to the junction box using junction box
screws, fasten it to the wall using wood screws (C).
Note: (i) using any other non-original-manufacturer provided
junction box screw may result in safety issues; (ii) The side of
the mounting plate marked GND must face out.
Fig. 2: Connecting the Wires
8. Hook the safety cords to the mounting plate.
9. Connect the driver input/output wires with junction box wires as
shown in Fig.2, making sure that all wire connectors (A) are
secured. If your outlet box and hardware are not UL approved,
please purchase separately.
Fixture Wires:
– Black or Smooth
– White or Ribbed
– Bare wire (Ground)
House Wires:
– Black (Hot)
– White (Neutral)
– Green or Bare Copper (Ground)
Fig. 3: Switch
The switch in the canopy can be used to adjust the color
temperature of the lamp between 3000K, 3500K, and 4000K.
Fig. 4: Back Plate Dimensions
The backplate dimensions can be used for reference during
installation.
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fixture BPD74232
Fig. 2 Wiring
Fixture Wires Black or Smooth
Fixture Wires White or Ribbed
Fixture Wires Bare wire (Ground)
House Wires Black (Hot)
House Wires White (Neutral)
House Wires Green or Bare Copper (Ground)
Fig. 3 Switch
3000K 3500K 4000K
Back Plate Dimensions
Fig. 4
GreenBlack White +
Cable(Cut) HARDWARE
brown Black –
Red +
3000K 3500K 4000K
Black –
Red +
Output
Input
Driver
White – Neutral Black – Hot
Purple – Dim+ Pink or gray – Dim-
Canopy
A
B
C
D
Wire Connector Qty: 3PCS+1 Extra
Mounting screw Qty: 3PCS+1 Extra
Wood screw Qty: 3PCS+1 Extra
Plastic anchor Qty: 3PCS+1 Extra
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901| Phone: 1-800-836-1892 | Fax: 518-563-4228 www.schonbek.com | JAN 2021 | 4
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901 Phone: 1-800-836-1892 | Fax: 518-563-4228 | www.schonbek.com
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fixture BPD74232
ASSEMBLY & INSTALLATION INSTRUCTIONS
Fixture BPD74232
Fig. 1
junction box Wire Connector A
Safety Cords Junction Box Screw
Wood Screws C
Cable-gripper
Push up
Adjust the fixture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
U.L. Approved 200LB.Max. Outlet Box and Hardware (Sold Separately) Plastic anchor D Ground Wire Mounting Backplate 3CCT Switch Mounting Screw B
Driver
Cloud Crystal RPL-GLA-74232
Spring sheet
Fixture
WARNING
IMPORTANT: NEVER attempt any work without shutting off the electricity. o Read all instructions before installing. o System is intended for installation in accordance with the National Electrical Code
(NEC), other applicable installation code(s) and local regulations by a licensed electrician familiar with the operation of the product and the hazards involved. o Go to the main fuse box, or circuit breaker panel. Place the main power switch in the “OFF” position and unscrew the fuse (s) or switch “OFF” the circuit breaker switch (es) that control the power to the fixture (s) or room that you are working on. o Place the wall switch in the “OFF” position. o FAILURE TO INSTALL THIS FIXTURE IN ACCORDANCE WITH THESE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND/OR PROPERTY DAMAGE. CAUTION o All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL Listing of this fixture. o When handling the fixture, do not apply pressure to the LEDs or bulbs. Hold the fixture by the base only. o Do not exceed maximum wattage noted on the fixture. Use only the recommended LED or standard lamps with the fixture.
ADVERTENCIA
IMPORTANTE: NUNCA trate de hacer ningún trabajo sin desconectar la electricidad. o Lea todas las instrucciones antes de instalar. o El sistema tiene por objeto la instalación de acuerdo con el Código Eléctrico
Nacional, y otros códigos de instalación y reglamentos locales aplicables, por parte de un electricista autorizado que esté familiarizado con el funcionamiento del producto y los peligros involucrados. o Vaya a la caja de fusibles o al panel de disyuntores principal. Ponga el interruptor principal de alimentación en la posición de “APAGADO”, y desenrosque los fusibles o “DESCONECTE” los disyuntores que controlen la alimentación a los dispositivos o la habitación en los que usted esté trabajando. o Ponga el interruptor de pared en la posición de “APAGADO”. o EL HECHO DE NO INSTALAR ESTE DISPOSITIVO DE ACUERDO CON ESTAS INSTRUCCIONES PODRÍA RESULTAR EN UNA LESIÓN PERSONAL GRAVE O LA MUERTE, Y/O DAÑOS A LA PROPIEDAD.
PRECAUCIÓN o Todas las piezas deben usarse como se indica en estas instrucciones.No
sustituya ninguna pieza, no deje piezas fuera, ni utilice ninguna pieza que esté desgastada ni rota. El hecho de no seguir estas instrucciones podría invalidar la certificación ETL/CETL de este dispositivo. o Al manipular el dispositivo, no aplique presión a los LED ni las bombillas. Sujete el dispositivo solo por la base. o No exceda la potencia máxima indicada en el dispositivo. Use solo los LED o las bombillas estándar recomendados con el dispositivo.
ADVERTENCIA
IMPORTANTE: NUNCA trate de hacer ningún trabajo sin desconectar la electricidad. IMPORTANT : Ne JAMAIS entreprendre des travaux sans couper l’électricité. o Lire toutes les instructions avant l’installation. o Ce système est conçu pour être installé conformément au Code national de
l’électricité ou d’autres codes d’installation et réglementations locales en vigueur par un électricien agréé connaissant le fonctionnement de ce produit et les dangers qu’il comporte. o Aller à la boîte à fusibles ou panneau principal de disjoncteurs. Placer l’interrupteur d’alimentation principal sur « ARRÊT » et dévisser le ou les fusibles ou mettre sur « ARRÊT » le ou les disjoncteurs qui contrôlent l’alimentation du ou des appareils électriques ou de la pièce dans laquelle vous travaillez. o Mettre l’interrupteur mural sur « ARRÊT » . o NÉGLIGER D’INSTALLER CET APPAREIL CONFORMÉMENT À CES INSTRUCTIONS RISQUE D’ENTRAÎNER DE GRAVES BLESSURES PERSONNELLES OU LA MORT AINSI QUE DES DOMMAGES MATÉRIELS. o MISE EN GARDE o Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ne remplacer aucune pièce, ne laisser aucune pièce de côté ou n’utiliser aucune pièce usée ou cassée. Le non-respect de cette directive peut invalider l’homologation ETL/CETL de cet appareil. o Lors de la manipulation de cet appareil, n’appliquer aucune pression sur les DEL ou les ampoules. Maintenir l’appareil par la base uniquement. o Ne pas dépasser le nombre de watts maximum indiqué sur l’appareil. N’utiliser que les DEL ou ampoules standard recommandées dans cet appareil.
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901| Phone: 1-800-836-1892 | Fax: 518-563-4228 www.schonbek.com | JAN 2022 | 2
PREPARATION 1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar. 2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation. MOUNTING THE Crystal AND FIXTURE (Fig. 1and Fig.3) 3. Install from the inside, the Cloud crystal against the spring sheet, press hard, the two convex points of the crystal are aligned with the two holes of
the fixture, so that the spring can automatically return. 4. Remove the mounting screw (B) from the fixture. 5. The lamp can switch between three color temperatures (3000k-3500k-4000k), which can be adjusted to your preference with the switch in the
canopy (Fig.4). 6. Drill holes in the wall aligned with the key holes located in the mounting back plate, insert the plastic anchor (D). 7. Secure the mounting plate to the junction box using junction box screws. fasten it to the wall using wood screws (C).
Note: (i) using any other non-original-manufacturer provided junction box screw may result in safety issue; (ii) The side of the mounting plate marked “GND” must face out.
8. Adjust the fixture wire length by pushing the cable gripper on the canopy and pulling the wire as desired. a. Retract these wires close to a desirable length to within the canopy before securing the fixture in place.Note: retracting or extending excessive cable length through the cable gripper is not recommended. b. Warning: Shortening these cables without professional helps or electronic background is not advisable. Any modifications to the fixture may result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig. 2) 9. Hook the safety cords to the mounting plate. 10. Connect the driver input/output wires with junction box wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare c opper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate usingthe screw provided. After wires are connected, tuck them carefully inside the junction box. 11 Secure the fixture by mounting the canopy to the ring of the backplate. Turn and rotate the canopy until it stops. Fasten the canopy to the back plate using the mounting screw (B). NOTE: DIMMING WIRING INFORMATION (Fig. 4) 12 This fixture features electronic low voltage (ELV or TRAIC) or 0-10V dimming capabilities. See notes below for specific dimming wires information. 13 To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground). 14. To utilize 0-10V dimming: use wire purple (dim+), Pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901| Phone: 1-800-836-1892 | Fax: 518-563-4228 www.schonbek.com | JAN 2022 | 3
Schonbek 1870 | Lighting that Lives Forever
