Nathan James 15402 Richie Bath In A Box 2-light Bathroom Vanity Light Fixture Instruction Manual

15402 Richie Bath In a Box 2-Light Bathroom Vanity Light Fixture

Product Information

Product Usage Instructions

Safety Instructions

• Do not modify the structure of this product in any way.
• Use this light fixture responsibly with the primary concern for
  your safety.
• Follow assembly instructions carefully and inspect product upon
  receipt and each use.
• Nathan James and its parent companies cannot be held legally
  responsible for any injuries or death resulted from failure to
  follow instructions or improper use of this product.
• Our products have been tested to meet specific safety measures
  as they were originally intended to be sold. Any modifications will
  present the risk of creating significant safety issues which Nathan
  James will not be responsible for.

Proper Use

• DO NOT use for commercial purposes.
• DO NOT leave spilled liquid on fixture.
• DO NOT use light fixture if damaged.
• DO NOT make temporary repairs.
• DO NOT use outdoors.

Important Instructions

1. Do not tighten bolts / screws completely until all bolts /
   screws are lined up and inserted into holes.
2. Do not over tighten screws and bolts to avoid stripping.
3. Please use hand tools to assemble this product. Do not use
   power tools.

Pre-Installation

Step 1

Thread the middle post section into the back of the Fixture (1)
and remove the Socket Rings (2).

Step 2

Secure the back plate of the Fixture (1) to the middle post
section using the provided hardware. Tighten with the Wrench (D) to
80%.

Step 3

Attach the Shades (3) to the Fixture (1) using the Socket Rings
(2).

Let’s build the
Richie Bath-in-a-box
SKU 15402
5 MINUT
75
SSEMBL

7 Y

E A

Scan me!
Inspiration Digital Instructions Free Lifetime Warranty

22-1116

Ok, let’s get rolling
This should be easy, just follow our instructions and you will be back to Netflix in no time.
Estimated time for assembly
75:00
What you need · Your favorite snack or energy bar
(Save the bubbly for once your fixture is safely installed!) · Use the packaging carton as a working surface to prevent product damage during assembly · Level · Phillips head screwdriver · Pencil · Drill with 1/4″ drill bit (for non-drywall) or 5/16″ drill bit (for drywall)
Toll-free at 1-866-619-1004 [email protected] Nathanjames.com/help
Scan me!
Inspiration Digital Instructions Free Lifetime Warranty

What’s included

Description

Qty

1 Fixture

1

2 Socket Ring

2

3 Shade

2

4 Left Towel Bar Support

1

5 Right Towel Bar Support

1

6 Towel Bar

1

7 Towel Hook

1

8 Left Toilet Paper Holder Unit

1

9 Right Toilet Paper Holder Unit

1

10 Towel Ring

1

A M4*26mm Screw

2

B Wire Nut

3

C Mounting Bracket

1

D Wrench

1

E Finial Nut

2

F Mounting Plate

6

G Drywall Anchor

12

H

M3.5*50mm Screw for Drywall Anchors

12

I Non-drywall Anchors

12

J

M3.5*35mm Screw for Non-Drywall Anchors

12

2

Safety first, fun later

Safe use of this product starts with you.

Do not modify the structure of this product in any way.

Use this light fixture responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect product upon receipt and each use.
Nathan James and its parent companies cannot be held legally responsible for any injuries or death resulted from failure to follow instructions or improper use of this product.

Our products have been tested to meet specific safety measures as they were originally intended to be sold. Any modifications will present the risk of creating significant safety issues which Nathan James will not be responsible for.

Proper use

DO NOT DO NOT DO NOT DO NOT DO NOT

use for commercial purposes leave spilled liquid on fixture use light fixture if damaged make temporary repairs use outdoors

WARNING
Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please reach out to our Customer Happiness team at [email protected] or 1-866-619-1004

WARNING: RISK OF ELECTRIC SHOCK
Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off at the switch is NOT SUFFICIENT to prevent electrical shock. PLEASE CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.

3

The goods
1

2

3

4

5

6

7

8

9

10

A

B

C

D

E

F

G

H

I

J

IMPORTANT 1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes. 2. Do not over tighten screws and bolts to avoid stripping. 3. Please use hand tools to assemble this product. Do not use power tools.
4

Pre-Installation
· Read all instructions prior to beginning assembly. · To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or
cardboard. · Keep the receipt and these instructions for proof of purchase. · Suggested Bulb: Type G50 · Max. Wattage: 120W (60W per bulb)

Step 1
Okay, time to get started! Don’t worry, we made the first step extra easy. Thread the middle post section into the back of the Fixture (1) and remove the Socket Rings (2).

Helpful tip: Righty-tighty, lefty-loosey!

1

2 2

5

Step 2

Secure the back plate of the

1

Fixture (1) to the middle post

section using the provided

hardware. Tighten with the

Wrench (D) to 80%.

D

Step 3
You’re doing great! Are you a professional or something? Now it’s time to attach the Shades (3) to the Fixture (1) using the Socket Rings (2).

1 3

2
6

Step 4
You’re almost halfway done installing the light fixture! Time for a snack break… Okay, back to work. Now it’s time to make sure your fixture will be nice and level when it’s installed. To do this, turn the round plate on the back of the Fixture (1) to ensure the holes in the round plate are horizontal/level. You can place the Fixture (1) on a table top to help with this step. Once the holes in the plate are horizontal, secure the nut on the back of the round plate using the Wrench (D).
1
D
7

Step 5

Remove the Finial Nuts (E) from

E

the Mounting Bracket (C).

C

E

Step 6
Okay, now for the fun part. Install the Mounting Bracket (C) to your pre-installed electrical box using the Junction Box Screws (A). Tighten using a Phillips head screwdriver.
C
A

Adjusting to level

Note: Be sure that you are only making the connections to a 120V AC 60Hz circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.
8

Step 7
Now wrap the ground wire around the grounding screw on the Mounting Bracket (C). Secure by tightening the screw using a Phillips head screwdriver.
Step 8
Join the matching colored wires (white to white, black to black, and ground to ground) with Wire Nuts (B). Tuck the excess wire into the electrical box.
B
B B
9

Step 9
Now it’s time to secure the Fixture (1) to the Mounting Bracket (C) on your preinstalled electrical box using the Decorative Nuts (E). Be sure that you have all of the excess wire tucked into the electrical box.

EE

To properly fasten the Decorate Nuts (E), thread in or out to adjust for proper threading length.

Step 10
Now for the final touch: install the light bulbs! We recommend 2 type G50 bulbs with a maximum wattage of 60 watts each (120W total). And voila, let there be light!
Troubleshooting

Use 2 type G50 bulbs (not included) 120V 60Hz AC only

Problem

Possible Causes

The bulb will not light.

The bulb is burned out.

The power is off.

The fuse blows or circuit breaker blows when the light is turned on.

The circuit breaker is off. There is an exposed wire.

Solutions
Replace the light bulb.
Ensure the power supply is on.
Ensure the circuit breaker is in the ON position. Discontinue use of the light. Contact a qualified electrician or reach out to our Customer Happiness team at [email protected] or 1-866-619-1004.

10

Step 11

Onto the bathroom hardware!

F

For each component, use a

Mounting Plate (F) as a template

for where you will need to drill

your holes on the wall.

For the towel bar, you will be using 2 Mounting Plates (F) with their centers 635mm apart from one another.
Use 1 Mounting Plate (F) as your first template to mark your first set of holes, then measure 635mm from the center of those marks and use the other Mounting Plate (F) to mark your second set of holes.

635mm F

F

11

Step 11 (cont.)

For the toilet paper holder, you will be using 2 Mounting Plates (F) with their centers 162mm apart from one another.

162mm

Use 1 Mounting Plate (F) as your first

template to mark your first set of holes,

then measure 162mm from the center of

F

those marks and use the other Mounting

Plate (F) to mark your second set of holes.

F

Important Note: Make sure the mounting plates are level with one another and the ground.

12

Step 12
Using a drill and the reference marks from Step 11 as a guide, drill your holes into the wall.

Important Note: For non-drywall anchors, use a 1/4″ drill bit. For drywall anchors, use a 5/16″ drill bit.

Step 13
Insert Wall Anchors (I) or (G) into the newly drilled holes.

Please Note: Part I is for non-

I

drywall applications. Part G

is for drywall applications.

G

13

Step 14
Using the provided screws (H) or (J) and newly installed Wall Anchors (G) or (I), mount the Mounting Plates (F) to the wall.

G or I

F
Please Note: Parts I and J are for non-drywall applications. Parts G and H are for drywall applications.

Step 15
Place the Towel Bar (6) between the 2 Towel Bar Support components (4) and (5).
6 4

H or J 5

14

Step 16
To mount each bathroom hardware component, first loosen the set screw(s) on the bottom of the bathroom hardware component. Then, mount that bathroom hardware component over the Mounting Plates (F), and secure in place by re-tightening the set screw(s).
5 4
5 4
15

Step 17
Repeat Step 16 for the Towel Hook (7) installation.
7
F 7
16

Step 18

10

Repeat Step 16 for the Towel Ring (10) installation.

F 10
17

Step 19
Repeat Step 16 for the Left Toilet Paper Holder Unit (8) installation.
8
F F
8
18

Step 19 (cont.)
Repeat Step 16 for the Right Toilet Paper Holder Unit (9) installation.
F
8 9
F
8 9
Toilet Paper Installation (toilet paper not included)
19

Questions? Don’t worry, we’ve got the answers

What other light bulbs can fit in this light?
The bulb must not be greater than the max wattage for the fixture (120W, 60W per bulb). It must match the base size, and the diameter of any area of the bulb should be less than diameter of any area of shade, so that it can fit.
Can I use an LED light bulb?
Yes, so long that the base size matches and the diameter of any area of bulb is less than diameter of any area of shade, so that it can fit.
Is this UL/ETL certified?
Yes, all our products are either UL or ETL.
Do I need an electrician to set up the hardwire?
We recommend using a certified electrician for all hardwiring, although all of our fixtures can be set up without an electrician, as long as you are replacing an existing fixture or have an existing junction box ready for a fixture installation. ENSURE POWER IS OFF WHEN INSTALLING. For all new constructions, please use a certified electrician.

Is this light compatible outside North America?
Our lighting is only warranted in Canada and the United States.
What do I do if the product is not working?
Try a different light bulb and confirm proper installation.
Can these lights work on a dimmer?
Dimmability is related to the light bulb and the wall switch, not the light fixture. All our hardwire fixtures are compatible with dimmable light bulbs. We recommend using a dimmer switch, as it extends the life of the bulb and allows for energy saving and great ambiance. If using a LED bulb, please ensure both your LED bulb and dimmer switch are compatible.
Can I use the fixture outdoors?
For vanity light fixtures, we have a damp rating, which approves the use in bathrooms or other damp areas, but is not approved for outdoor use unless specified.

Can I retrofit this hard-wired to a plug-in or vice-versa?
Yes, a plug-in fixture can be turned into a hardwire fixture and a hardwire fixture can become a plug-in fixture. For many products we will provide all the necessary hardware to make these changes, if not, you will need to purchase the necessary hardware.

20

No heartburn, when we handle the return
Give us a call 1-866-619-1004 or shoot us a message at [email protected] we will issue you a free replacement with zero hassle.

Our way
Give us a call Replacement You

Their way
Re-package item Schedule pick up Track package Replacement You

We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.

21

We are only in business if you’re happy
For starters, thanks for being you.
Toll-free at 1-866-619-1004 [email protected] NathanJames.com/help
We do our best to ensure your product arrives without any problems, but occasionally mistakes happen–as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free.
Warranty This product comes with a lifetime warranty from the date of purchase. Please use your phone to scan the QR code to register your product or visit https://goo.gl/i9dk3q
Did we do alright? Please spread the love! If you are happy with your product, tell your friends and family about us or even better leave us a review online. Spreading the word gives us the opportunity to make more people happy and keep our prices low for your next purchase.
Brooklyn Burdon
Founder, Nathan James
22

References

• Support : Nathan James
• Product Warranty | Nathan James