Product Information

The LED Backlit Panel is a type of light fixture that provides a
bright and energy-efficient lighting solution. It comes in four
different models: BLP16W-30/60-CC, BLP36W-120/30-CC,
BLP36W-60SQ-CC, and BLP45W-120/60-CC. The panel is designed for
recessed installation, and there are two methods available for this
type of installation. The panel comes in different sizes, and the
cutout size needed for installation depends on the panel size.
Clips should be purchased separately as an accessory.

Safety Instructions

Before installing the LED Backlit Panel, make sure that the
mounting surface or structural member used for installation can
support the weight of the panel. Also, ensure that the circuit is
switched off before starting the installation and switched on only
after complete installation and examination of the circuit. The
lamp inspection should be done before installation to ensure that
the fitting is not warped.

Product Usage Instructions

Choose the appropriate recessed installation method based on
your preference.
Check the cutout size required for your panel size from the
table provided in the user manual.
If necessary, purchase clips as an accessory.
Ensure that the mounting surface or structural member used for
installation can support the weight of the panel.
Switch off the circuit before starting the installation.
Inspect the lamp before installation to ensure that it is not
warped.
Select the appropriate color temperature before installation
using the slide switch with corresponding color temperature.
Install the panel according to the chosen method and spacing
requirements provided in the user manual.
Switch on the circuit only after complete installation and
examination of the circuit.

It is important to note that the input wire diameter should be
0.75mm2, and product modification and improper installation are not
valid for warranty. Additionally, the light source contained in
this luminaire should only be replaced by the manufacturer or a
qualified person.

View Fullscreen

Recessed Installation | Method 1

34 Recessed Installation | Method 2

Cutout Size

Panel Size

Cutout

Panel Size

Cutout

295x295mm 270x270mm 620x620mm 590x590mm

295x595mm 270x570mm 295x1195mm 270x1170mm

595x595mm 570x570mm 595x1195mm 570x1170mm

Clips should be purchased separately as an accessory
12

COMPLETE
Ceiling opening based on cutout size

2 1

56
1800 909 306

COMPLETE
nedlandsgroup.com.au [email protected]

Certainty at The Speed of Light
INSTALLATION MANUAL
LED BACKLIT
PANEL
BLP16W-30/60-CC BLP36W-120/30-CC BLP36W-60SQ-CC BLP45W-120/60-CC

Safety Instructions
Basic safety precautions should always be followed when installing, including the following: 1. Read instructions carefully before installing. 2. This LED Panel requires professional installation and maintenance. 3. The power supply of the LED Panel should be powered by a dedicated external LED driver. 4. Disconnect the power supply before installing or maintenance. 5. Make sure the wires have been properly connected before powering on the device. 6. Ensure the product has enough space for heat dissipation. 7. Ensure the luminaries are never covered by any heat insulation mat or slim layer material at anytime. 8. IP40 for indoor use only, not for damp locations. 9. Storage Conditions: Cool & dry conditions.
10. Ambient Temperature: -10° to +40°. Avoid direct sunlight. 11. Please ensure the LED driver is situated either on back of fitting or suspended above fitting, and that the driver
is clear of any insulation.
Installation Procedure

WARNING:
1. Switch off before installation. 2. Switch on only after complete installation and examination of the circuit.

CAUTION:
Make sure that the mounting surface or structural member used for installation can support the weight of LED Panel.

Please select colour temperature before installation, see below picture. Choose colour by slide switch with corresponding colour temperature.

CW (5700K) NW (4000K) WW (3000K)
5000K 4000K 3000K

Lamp inspection before installation: Take out the fitting from the box and place it on a flat table. If the fitting is warped, please adjust the fitting by following the steps below before installation:
1. Press the opposite angles at the same time; 2. Press the other two opposite angles at the same time, make
sure the four angles are flat, then start the installation.
Installation Spacing

Surface Mount Installation

Pendant Installation

RISK OF FIRE – Required clearance from structural members and building elements

SCB=25mm

HCB=25mm

MIC=0mm

SCI=0mm

HCB: MIC: SCI: SCB:

Height clearance to building element Minimum insulation clearance Side clearance to insulation Side clearance to building element

WARNING – RISK OF OVERHEATING OR FIRE IF THE CLEARANCE DISTANCES ARE COMPROMISED
Warning:
Input wire diameter 0.75mm2 ; Product modification and improper installation are not valid for warranty!
The light source contained in this luminaire shall only be replaced by the manufacturer or a qualified person.

Press to adjust the length of zhe suspention wire

12 34

COMPLETE COMPLETE