N1854-707 Four Light Bath Bar in Sand Coal
Product Information
The product is a light fixture with item number N1854-707,
manufactured on April 18, 2022. The installation instructions warn
the user to shut off the power at the fuse box or circuit breaker
before installation. The preparation steps involve removing the old
fixture and laying out the new fixture’s parts in a clean area
without misplacing any small parts necessary for installation. The
circular strap is attached to the junction box using mounting
screws, and the side of the circular strap marked GND must face
out. The product comes with fixture wires, black or smooth, white
or ribbed, and bare copper (ground), while house wires consist of
black (hot), white (neutral), and green (ground).
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box.
- Remove the old fixture including the mounting hardware.
- Unpack the new fixture carefully and lay out all parts in a
clean area without misplacing any small parts necessary for
installation. - Thread two mounting screws (A) into pre-drilled holes in the
circular strap (B), spaced the same distance apart as the holes in
canopy (D). Adjust the screw length if necessary. - Attach circular strap (B) to junction box (not included) using
mounting screws (C) (Size: #8-32N*L0.5). Ensure that the side of
the circular strap marked GND faces out. - Connect the electrical wires as shown in Fig. 2:
- Connect house wires black (hot) to fixture wires black or
smooth. - Connect house wires white (neutral) to fixture wires white or
ribbed. - Connect house wires green (ground) to fixture wires bare copper
(ground).
Note: The illustration in Fig. 1 is for installation purposes
only and may or may not be identical to the fixture purchased.
INSTALLATION INSTRUCTIONS
Item#N1854-707 (New. 2022/04/18) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the
parts in a clean area. Take care not to misplace any small parts necessary for installation. 3. Thread two mounting screws (A) into pre-drilled hole in
circular strap (B). Spaced same distance apart as the
holes in canopy (D), The length of screws (A) may be
adjusted if necessary.
4. Attach circular strap (B) to Junction box (not included) using mounting screws (C) (Size: #8-32N*L0.5″). The side of the circular strap (B) marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2) 5. At this point, connect the electrical wires as shown in
figure 2, making sure that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to circular strap (B) using green screw provided. COMPLETING THE INSTALLATION (Fig. 1) 6. Place fixture body (D) onto mounting screws (A) and secure with knurled knobs (E). 7. Place glass shade (G) over socket (F) and secure with screw shell (H). 8. Install (4) four candelabra base bulbs (I) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Fig. 1 Set# A-020 -Circular Strap -Ground Screw -Mounting Screw*2
A BC
Fig. 2 FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
HOUSE WIRES Black (Hot)
D
HOUSE WIRES White (Neutral)
E
FIXTURE WIRES Bare Copper (Ground)
I H G F
HOUSE WIRES Green (Ground)
Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
LA-3552E
