2694-115 Yorkville 4-Light Aged Darkwood with Silver Patina Pendant
Product Information
The product being discussed is Item#2694-115, which is a new
fixture that was manufactured on 25th February 2022. This product
comes with installation instructions that must be read and saved
for future reference. The product package includes a mounting
plate, ground screw, mounting screw x 2, rod x 1, candle cover, and
fixture wires. The fixture wires are made up of black or smooth,
white or ribbed, and bare copper (ground) wires. The product manual
also contains a diagram (Fig. 1) showing the parts included in the
package.
Product Usage Instructions
- Before starting the installation process, switch off the power
at the fuse box or circuit breaker box. - Remove the old fixture, including the mounting hardware.
- Unpack your new fixture carefully and lay out all the
parts. - Refer to the diagram in Fig. 1 of the manual to familiarize
yourself with the parts included in the package. - Attach the mounting plate to the junction box using the
mounting screws provided. - Connect the fixture wires to the house wires. The black or
smooth wire should be connected to the black (hot) wire, the white
or ribbed wire should be connected to the white (neutral) wire, and
the bare copper wire should be connected to the green (ground)
wire. - Attach the fixture to the mounting plate using the rod
provided. - Attach the candle cover to the fixture.
- Turn on the power at the fuse box or circuit breaker box.
- Test the fixture to ensure it is working correctly.
Note: The diagram in Fig. 1 is for installation purposes only
and may or may not be identical to the fixture purchased.
INSTALLATION INSTRUCTIONS
Item#2694-115 (New. 2022/02/25) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S H U T P O W E R O F F AT F U S E O R CI RC U I T BR E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig.1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts
in a clean area. Take care not to misplace any small parts necessary for installation. 3. Secure rod (J) onto all thread (K) on the fixture body. 4. Pass arm (H) through all thread (I) and insert both ends into location pins (L). Secure rod (G) onto all thread (I) on rod (J). 5. Determine the desired hanging height and thread rods (F1, F2 and F3) to the all thread on rod (G). Attach canopy (D) by screwing onto rod (F1). Carefully pass the wires through each rod during assembly. Note: Remove the all thread, if installing with one 6″ rod only. 6. Attach mounting plate (A) to the junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5″). The side of the mounting plate (A) with “GND” marked on it and two convex points must face out. 7. The support cable is provided to support the weight of the fixture while wiring. Align the fixture to mounting plate (A) and attach hook (P) on the end of support cable (C) into a slot located on mounting plate (A). Carefully allow support cable (C) to support the weight of the fixture while wiring (Fig.1). CONNECTING THE WIRES (Fig. 2) 8. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. 9. Tuck wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1) 10. Place canopy (D) over mounting plate (A) and secure with screws (E). 11. Place candle covers (N) over sockets (O). 12. Install (4) four candelabra base bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. –DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the junction box and test the fixture.
Fig. 1 Set#A-021-118DH -Mounting plate -Ground screw -Mounting screw*2
F1
F2 F3 G
K
P
A B C D E
Rod# W30-1-767*1(F1) W30-1-767 *2(F2) W30-H-767 *1(F3)
H I J L
M
N O
Candle cover# CCV24049P-767
Fig. 2 FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Bare Copper (Ground)
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page: 1/1
LA-3516E
