Minka Lavery 2164-66a Pendant Instruction Manual (+ PDF)

Contents hide

2164-66A Pendant

Product Information:

The product is Item#2164-66A, a new fixture that was
manufactured on July 27, 2021. The fixture comes with a mounting
plate (A), ground screw, mounting screws (B), canopy (D), four rods
(F1, F2, F3, G), all thread (H), and candelabra base bulbs (I)
which are not included and must be purchased separately. The
fixture can accommodate up to four candelabra base bulbs or CFL/LED
equivalents, not exceeding 60 watts each. The installation process
involves shutting off the power supply, removing the old fixture,
and installing the new fixture using the provided mounting hardware
and wiring.

Product Usage Instructions:

Before starting the installation process, shut off the power at
the fuse box or circuit breaker box.
Remove the old fixture and its mounting hardware.
Unpack the new fixture and lay out all parts in a clean
area.
Secure rod (G) onto all thread (H) on the fixture body.
Determine the desired hanging height and thread rods (F1, F2,
F3) to the all thread on rod (G).
Attach canopy (D) by screwing onto rod (F1). Carefully pass the
wires through each rod during assembly. Remove all thread if
installing with one 6 rod only.
Attach the mounting plate (A) to the junction box with mounting
screws (B). The side of the mounting plate (A) with GND marked on
it and two convex points must face out.
Connect the electrical wires as shown in fig 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly
to the mounting plate (A) using the green screw provided.
Place canopy (D) over mounting plate (A) and secure with screws
(E).
Install four candelabra base bulbs (I) up to 60 watts each or
CFL/LED equivalent (not included) in accordance with the fixture
specification. Do not exceed the maximum wattage rating.
Once installation is complete, turn on the power supply and
test the fixture.

View Fullscreen

INSTALLATION INSTRUCTIONS

Item#2164-66A (New. 2021/07/27) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION (Fig.1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts
in a clean area. Take care not to misplace any small parts
necessary for installation. 3. Secure rod (G) onto all thread (H) on the fixture body. 4. Determine the desired hanging height and thread rods
(F1, F2 and F3) to the all thread on rod (G). Attach canopy
(D) by screwing onto rod (F1). Carefully pass the wires
through each rod during assembly. Note: Remove the all
thread, if installing with one 6″ rod only. 5. Attach the mounting plate (A) to the junction box (not
included) with mounting screws (B) (Size: #8-32N*L0.5″).
The side of the mounting plate (A) with “GND” marked on
it and two convex points must face out.
CONNECTING THE WIRES (Fig. 2) 6. Connect the electrical wires as shown in fig 2, making
sure that all wire connectors are secured. If your junction
box has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the mounting plate (A) using the
green screw provided. 7. Tuck wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1) 8. Place canopy (D) over mounting plate (A) and secure with
screws (E). 9. Install (4) four candelabra base bulbs (I) up to 60 watts
each or CFL or LED equivalent (not included) in
accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)