2294-613 Via Roma Pendant
Product Information
The product is a light fixture with the item number 2294-613. It
comes with a circular strap, ground screw, mounting screw, and
three medium base bulb sockets that can hold up to 60 watts each.
The fixture is compatible with CFL or LED bulbs as well. The
fixture has a maximum wattage rating that should not be exceeded.
The product requires electrical wiring for installation and comes
with a support cable to aid in the installation process.
Product Usage Instructions
- Shut off the power at the fuse box or circuit breaker before
beginning installation. - If necessary, remove the existing fixture and its mounting
hardware from the ceiling. - Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration. - Connect cable and fixture body together by threading nuts (I)
at the end of cable into all thread (J) on fixture body. Adjust
cable length by pushing wire strainer to keep fixture level. - Thread screws (A) into the pre-drilled holes of the circular
strap (B) spaced the same distance apart as the holes in the canopy
(D) of the fixture body. The length of screws (A) may be adjusted
if necessary. - Attach circular strap (B) to the outlet box using the two
mounting screws (C). The side of the circular strap (B) marked GND
must face out. - Determine the desired hanging height by pushing or pulling the
cord through the center of metal bushing (E). Secure the cord by
tightening metal screw (F) into the metal bushing (E). Cut excess
wire leaving about 6 inches of cord for electrical
connections. - Carefully cut and remove approximately 4 inches of the outer
sheathing from the cord and strip 1/2 inch of the wire ends bare to
expose the copper strands. - Align the fixture to circular strap (B) and attach hook (L) on
the end of support cable (H) into a slot located on circular strap
(B). Carefully allow the support cable (H) to support the weight of
the fixture while wiring. - Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your outlet has a ground
wire (green or bare copper), connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire directly to the
circular strap (B) using the green screw provided. - Tuck the wire connectors neatly into the outlet box.
- Raise canopy (D) over mounting screws (A) and secure with
finials (G). - Install three medium base bulbs (K) up to 60 watts each or CFL
or LED equivalent (not included) in accordance with the fixture
specification — DO NOT EXCEED THE MAXIMUM WATTAGE RATING! - After completing the installation, return power to the outlet
box and test the fixture.
INSTALLATION INSTRUCTIONS
Item#2294-613 (New. 11/17/2021) READ AND SAVE THESE INSTRUCTIONS
W ARNI N G ! S HU T PO WE R O F F AT F USE OR CI RC UI T BRE AK E R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig. 1) 1. Shut off the power at the fuse box or circuit breaker. If
Fig. 1
necessary, remove the existing fixture and its mounting hardware from the ceiling. 2. Carefully remove the fixture from the carton and check that all parts are included as shown in the illustration. 3. Connect cable and fixture body together by threading nuts (I) at the end of cable into all thread (J) on fixture body. Adjust cable length by pushing wire strainer to keep fixture level.
Set# A-020-A – Circular strap – Ground screw – Mounting screw*2
A
L
B
C H D
4. Thread screws (A) into the pre-drilled holes of the circular strap (B) spaced the same distance apart as the holes in the canopy (D) of the fixture body. The length of screws (A) may
F E
be adjusted if necessary.
G
5. Attach circular strap (B) to the outlet box (not included) using
the two mounting screws (C) (size: #8-32N*L0.5″). The side of
the circular strap (B) marked “GND” must face out.
6. Remove metal screw (F) from metal bushing (E). Determine
the desired hanging height by pushing or pulling the cord
through the center of metal bushing (E).
7. Secure the cord by tightening metal screw (F) into the metal
bushing (E). Cut excess wire leaving about 6″ of the cord for
the electrical connections.
8. Carefully cut and remove approximately 4″ of the outer
sheathing from the cord and strip 1/2″ of the wire ends bare to
expose the copper strands.
9. The support cable is provided to support the weight of the
fixture while wiring. Align the fixture to circular strap (B) and
I
attach hook (L) on the end of support cable (H) into a slot
located on circular strap (B). Carefully allow the support cable
(H) to support the weight of the fixture while wiring (Fig.1).
J
CONNECTING THE WIRES (Fig. 2)
10. Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your outlet has a
ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap (B) using the green screw
provided. 11. Tuck the wire connectors neatly into the outlet box.
K
COMPLETING THE INSTALLATION (Fig. 1)
12. Raise canopy (D) over mounting screws (A) and secure with
finials (G).
13. Install (3) three medium base bulbs (K) up to 60 watts each or
CFL or LED equivalent (not included) in accordance with the fixture specification — DO NOT EXCEED THE MAXIMUM
WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the outlet box and test the fixture.
Note: The illustration in figure 1 on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Fig. 2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Bare Copper or Green (Ground)
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
LA-3504E
