Minka Lavery 2751-694 Ponderosa Ridge 1-light Weathered Spruce And Silver Hardwired Outdoor Wall Lantern Sconce Instruction Manual

2751-694 Ponderosa Ridge 1-Light Weathered Spruce and Silver Hardwired Outdoor Wall Lantern Sconce

Product Information

The product is an electrical fixture with item number 2751-694.
It comes with a circular strap, ground screw, mounting screws,
knurled knobs, rubber washers, and a large glass shade. The fixture
requires installation and should be connected to a junction box. It
is important to turn off the power at the fuse box or circuit
breaker before installing the fixture. The product is intended for
indoor use only.

Product Usage Instructions

1. Turn off the power at the fuse box or circuit breaker.
2. Carefully remove the old fixture and its mounting
   hardware.
3. Unpack the new fixture and lay out all the parts in a clean
   area.
4. Thread screws (C) into the pre-drilled holes in the circular
   strap (A) spaced the same distance apart as the holes in the back
   plate of the fixture body (D).
5. Attach the circular strap (A) to the junction box using
   mounting screws (B) with the side marked GND facing out.
6. Connect the electrical wires, making sure that all wire
   connectors are secured. Connect the fixture’s ground wire to either
   the junction box’s ground wire or directly to the circular strap
   (A) using the green screw provided.
7. Place fixture body (D) over screws (C) and secure with knurled
   knobs (E) and rubber washers (M) provided.
8. Place large glass shade (J) over socket (F) and twist to secure
   to the socket cup.
9. Turn on power at the fuse box or circuit breaker and test the
   fixture.

Note: The illustration in the manual (Fig. 1) is for
installation purposes only and may or may not be identical to the
fixture purchased.

INSTALLATION INSTRUCTIONS

Item#2751-694 (New. 2022/04/18) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig. 1)

Fig. 1

1. Shut of power at the fuse box or circuit breaker box and Set# A-020

J

remove the old fixture including the mounting hardware. -Circular Strap

2. Carefully unpack your new fixture and lay out all the -Ground Screw

parts in a clean area. Take care not to misplace any -Mounting Screw*2

small parts necessary for installation.

3. Thread screws (C) into the pre-drilled holes in the circular strap (A) spaced the same distance apart as the

L

holes in the back plate of the fixture body (D). The

length of screws (C) may be adjusted if necessary.

4. Attach the circular strap (A) to the junction box (not

I

included) using mounting screws (B) (Size:

#8-32N*L0.5″). The side of the circular strap marked

“GND” must face out.

H

CONNECTING THE WIRES (Fig. 2) 5. Connect the electrical wires as shown in figure 2,
making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (A) using the green screw provided. After the wires are connected, tuck them carefully inside the junction box.

A
B C DM E

COMPLETING THE INSTALLATION (Fig. 1) 6. Place fixture body (D) over screws (C) and secure with
knurled knobs (E) and rubber washers (M) provided. 7. To prevent moisture from entering the outlet box and
causing a short, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant) to outline the outside of fixture back-plate where it meets the wall leaving a space at bottom to allow moisture a means to escape (Fig.3). 8. Secure pine cone (K) to the metal stick on the fixture body (D). 9. Place small glass shade (G) over socket (F) and secure with socket ring (H) using socket spanner (I). 10. Install (1) one medium base bulb (L) up to 60 watts or CFL or LED equivalent (not included) in accordance with the fixture specification — DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
11. Place large glass shade (J) over socket (F) and twist to
secure to the socket cup.

Fig. 2 FIXTURE WIRES Black or Smooth
Fig. 3

FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)

G F
K

FIXTURE WIRES Bare Copper (Ground)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

Your installation is now complete. Return power to the junction box and test the fixture.

BACK PLATE

CAULKING

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Page: 1/1

LA-3564E