JYL7597A Victoria Rustic Midcentury Iron LED Chandelier
Product Information
The product is a lighting fixture with model number JYL7597A.
The dimensions of the product are 29 inches in diameter and a
height range between 27.5 inches to 86.5 inches. The product comes
with a mounting bracket, closable link, machine screw, lock washer,
threaded rod, ground screw, wire connector, canopy, hang loop,
chain, fixture loop, and six bulbs. The product is designed to
provide lighting to a room or space.
Product Usage Instructions
Warning: We recommend installation of this
lighting fixture be done by a licensed electrician. Switch off the
main electrical supply from the main fuse box/circuit breaker
before installation. Inspect item carefully before attempting to
install. If there is any damage or obvious defect, do not install.
Item may not be returned once it has been installed.
Notice and Important Safety Instructions:
- Please make sure that you have all parts indicated before you
begin assembly of this item. - This item should be assembled on a soft surface to prevent
scratching the finish during assembly. - To reduce the risk of fire, electrical shock or injury to
persons or property, please follow the guideline below for safe use
and installation. - The external flexible cable or cord of this lamp cannot be
replaced. If the cord is damaged, the lamp shall be destroyed.
Part List and Hardware List:
| Piece Description | Picture | Quantity | Piece Description |
|---|---|---|---|
| Mounting bracket |  | 1X | Closable Link |
| Machine screw |  | 2X | Canopy Nut |
| Lock washer |  | 1X | Chain (short) |
| Threaded rod |  | 1X | Fixture Loop |
| Ground screw |  | 1X | Column |
| Wire connector |  | 3X | Bulb |
| Canopy |  | 1X | Body |
| Hang loop |  | 1X |
Preparation:
Before beginning assembly of product, make sure all parts are
present. Compare parts with package contents list and hardware
contents list. If any part is missing or damaged, do not attempt to
assemble the product. Estimated Assembly Time: 20 minutes.
- Spread fixture arms of the body (O) to an equal distance
apart. - Thread the column (M) onto the body (O).
- Thread the fixture fixture loop(L) onto the nipple of the body
(O). - Connect chain(K) by fixture loop(L) and hang loop(H) with the
closable link(I). - Secure mounting bracket (A) to outlet box with machine screw
(B), Insert lock washer (C) and thread the short threaded rod(D)
onto mounting bar (A), then secure with the nut of the short
threaded rod(D). - Make wire connections, with wire connectors(F), following the
reference chart listed below. - Orient the ceiling canopy(G) so that the short threaded rod(D)
into the holes in the canopy, and thread the hang loop(H) onto the
short threaded rod(D), then secure it with the canopy nut(J).
Wire Connection Reference Chart:
| Wire Color | Outlet Supply Wire | Wire to Connect |
|---|---|---|
| Black or Red | Outlet Supply Wire | Black Cord (round & smooth) |
| Connect, Neutral, White | Outlet Supply Wire | White Cord (square & ridged) |
| Clear, Brown, Gold or Black without Tracer (colored stripes) | Wire to Connect | Insulated Wire (not green) with copper metal conductor |
| Clear, Brown, Gold or Black with Tracer (colored stripes) | Wire to Connect | Insulated Wire (not green) with Silver metal conductor. |
Grounding Instructions:
- For installation in the United States: Wrap ground wire from
outlet box around green ground screw(E) on mounting bracket, no
less than 2 from wire end. Tighten ground screw. If fixture is
supplied with a ground wire, connect to outlet ground wire with a
wire connector. - For installation in Canada: If fixture is supplied with ground
wire, wrap ground wire around green grounding screw on mounting
bracket. Tighten ground screw.
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION
A
mounting bracket
1X
I
closable Link
PICTURE QUANTITY 2X
B machine screw
2X
J
canopy Nut
1X
C
lock washer
1X
K
chain
1X
short
D
threaded rod
1X
L
fixture Loop
1X
E ground screw
1X
M
column
1X
F wire connector
3X
N
bulb
6X
G
canopy
1X
O
body
1X
H
hang loop
1X
1/2
Model#: JYL7597A Product Dimensions: 29″D X (27.5-86.5″)H
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1.Spread fixture arms of the body (O) to an equal distance apart. 2.Thread the column (M) onto the body (O). 3.Thread the fixture fixture loop(L) onto the nipple of the body (O). 4.Connect chain(K) by fixture loop(L) and hang loop(H) with the closable link(I). 5.Secure mounting bracket (A) to outlet box with machine screw (B),Insert lock washer (C) and thread the
short threaded rod(D) onto mounting bar (A), then secure with the nut of the short threaded rod(D). 6. Make wire connections, with wire connectors(F), following the reference chart listed below.
ack or Red Outlet Supply Wire to:
Black el Cord (round & smooth)
Connect, Neutral, White Outlet Supply Wire to:
White * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw(E) on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
7. Orient the ceiling canopy(G) so that the short threaded rod(D) into the holes in the canopy, and thread the hang loop(H) onto the short threaded rod(D), then secure it with the canopy nut(J).
8. Install bulbs(N). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
PLEASE USE ON/OFF TYPE”B” BULB MAX 40-WATT OR LED BULB MAX 9-WATT. THERE ARE 6PCS LED 4-WATT BULBS IN THE BOX
ENJOY YOUR LAMP
2/2
