George Kovacs P5436-697-l Astor 1 Light Soft Gold Modern/contemporary Led Chandelier Instruction Manual

P5436-697-L Astor 1 Light Soft Gold Modern/Contemporary LED Chandelier

Product Information

The P5436-697-L and P5437-697-L are fixtures that can be mounted
on a junction box. These fixtures are dimmable with ELV and/or LED
compatible wall dimmer switch. The package includes a mounting
plate, metal plate, canopy, swivels, and rods for fixture body
assembly. The fixture has a driver inside the canopy that needs to
be connected to the LED wires. The wires should be connected as per
the instructions provided in Fig. 2. The fixture has a ground wire
that needs to be connected to the junction box’s ground wire (if
available) or directly to the mounting plate using the green screw
provided. The installation of the fixture should be done by a
qualified electrician.

Product Usage Instructions

1. Carefully remove the fixture from the carton and check that all
   parts are included as shown in the illustration.
2. Shut off power at the circuit breaker and remove the old
   fixture including the mounting hardware.
3. Attach mounting plate (A) to junction box (not included) using
   mounting screws (B) (Size: #8-32N*L1L) as shown in Fig. 1. The side
   of mounting plate (A) marked GND must face out.
4. Determine the desired hanging height and thread rods (F1, F2,
   and F3) to all thread on fixture body. Carefully pass wires through
   each rod during assembly. Secure swivels (G) onto rods (F1).
5. Slide metal plate (E) and canopy (D) followed by lock washers
   (H) over swivels (G) and secure with hex nuts (I) via wrench (J)
   (not included).
6. Connect the driver output wire to the LED wires as listed
   below. Secure with wire connectors (I).
   • Red driver output wire (labeled Output+) to red LED wire
     (labeled LED+)
   • Yellow driver output wire (labeled Output-) to yellow LED wire
     (labeled LED-)
7. Connect the electrical wires as shown in Fig. 2, making sure
   that all wire connectors are secured. If your junction box has a
   ground wire (green or bare copper), connect the fixture ground wire
   to it. Otherwise, connect the fixture ground wire directly to the
   mounting plate (A) using the green screw provided.
8. Align canopy (D) over mounting plate (A) and secure with screws
   (C).
9. Adjust each frame on the fixture body as shown in Fig.3.

INSTALLATION INSTRUCTIONS
Item#P5436-697-L & P5437-697-L (Rev. 04/26/2022) READ AND SAVE THESE INSTRUCTIONS
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION 1. Carefully remove the fixture from the carton and check that all parts
are included as shown in the illustration. 2. Shut off power at the circuit breaker and remove the old fixture
including the mounting hardware.
MOUNTING THE FIXYURE (Fig. 1) 3. Attach mounting plate (A) to junction box (not included) using
mounting screws (B) (Size: #8-32N*L1″L) as shown in Fig. 1. Noted: The side of mounting plate (A) marked “GND” must face out. 4. Determine the desired hanging height and thread rods (F1, F2 and F3) to all thread on fixture body. Carefully pass wires through each rod during assembly. Secure swivels (G) onto rods (F1). 5. Slide metal plate (E) and canopy (D) followed by lock washers (H) over swivels (G) and secure with hex nuts (I) via wrench (J) (not included).
CONNECTION THE WIRES (Fig. 2) 6. There is one driver inside canopy, connect driver output wire to LED
wires as listed below. Secure with wire connectors (I). -Red driver output wire (labeled Output+) to red LED wire (labeled LED+) -Yellow driver output wire (labeled Output-) to yellow LED wire (labeled LED-)
7. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire
(green or bare copper), connect the fixtures ground wire to it.
Otherwise, connect the fixture ground wire directly to the mounting
plate (A) using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
FINISHING THE INSTALLATION (Fig. 1)
8. Align canopy (D) over mounting plate (A) and secure with screws (C).
9. Adjust each frame on the fixture body as Fig.3. Note:Illustration (Fig. 1) on this manual is for installation purpose only. It may or may not be identical to the fixture purchased.
Dimmable with ELV and/or LED compatible wall dimmer switch.

Fig. 1

Set#XXXX

– Mounting plate

A

– Ground screw

– Mounting Screw*2 J B

– Swivel*2

D

E G F1

F2

F3

Fixture body

Rod# – XXXX*2 (F1) – XXXX*4 (F2)
– XXXX*2 (F3)

Fig.2
FIXTURE WIRES Black or Smooth

FIXTURE WIRES White or Ribbed

Outlet box I H C
FIXTURE WIRES Bare Copper (Ground)

Fig. 3

HOUSE WIRES Black (Hot)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green or Bare Copper(G round)

IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

Page: 1/2

P5436-697-L & P5437-697-L

Fig.4 a. Hardware Bag A. Mounting Plate*1 D.Canopy*1 E.Metal plate*1 C.Mounting screw*2 G.Swivel*2
b. Hardware Bag: F1. ROD 6″*2 F2. ROD 12″*4 F3. ROD 12″*2

A

D

C

E

G

F2

F3

F1

Page: 2/2

P5436-697-L & P5437-697-L