A04993 8 Light Polished Gold Modern Contemporary LED Dry Rated Chandelier
Product Information:
Item Number: A04993
Maximum Wattage: LED, 40W
Product Usage Instructions:
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may
need it at a later time. - Before you start, NEVER attempt any work without shutting off
the electricity until the work is done. - Ensure that the mounting surface is clean, dry, flat, strong
enough, and 1/4 larger than the canopy on all sides. Correct any
gaps between the mounting surface and canopy exceeding 3/16 as
required. - Check if the ceiling or wall can support the weight of the lamp
before installation. - Make sure the voltage you are using is 120V. The maximum
wattage is LED, 40W. - Keep the lamp away from acidic and alkaline substances to avoid
damaging the surface. - When replacing bulbs, turn off or unplug the lamp and wait
until it is cool as bulbs get hot quickly. - Use common sense, caution, and care when using any electrical
products.
Assembly & Installation Instructions:
- Carefully remove the fixture from the carton and check that all
parts and accessories are included as shown in the provided
illustration. - Before starting the installation, turn off the power. NEVER
attempt any work without shutting off the electricity until the
work is done. - Remove the mounting plate (C).
- Screw the unit to the top of the base (M).
- Screw lampshades (I) to the top of lampholders (J) as shown in
the illustration. - Connect wires as per the provided wire connection chart. Note
that the ground wire is a bare copper wire and should never be
connected to other wires. - Connect the black or red supply wire to the appropriate outlet
box ground. - Connect the white supply wire to the fixture ground.
- Refer to the wire connection chart for further instructions
based on the type of wire used.
If you have any further questions or need assistance, please
contact our customer care team at +1 850 296 2377 during working
hours (Mon – Fri, 9:00 – 16:00 EST) or email us at
[email protected].
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
Item Number: A04993
WARNING (To reduce the risk of fire, electric shock, or personal injury): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at a later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation. 6. Make sure the voltage you are using is 120V. The maximum wattage is LED, 40W. 7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp. 8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
quickly. 9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It
must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED Before starting assembly and installation please prepare the needed (NOT INCLUDED): tools as below picture
Ladder
Philips Head or Flat Blade Screwdriver
Electrical Tape
Pliers
Wire Cutter/Stripper
Page: – 1 – / 4
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
PARTS TYPE & QTY INCLUDING: (C) Mounting plate (1) (D) Green ground screw (1) (E) Stud (2) (F) Canopy (1) (G) Swivel joint (1) (H) Tube (1) (I) Lampshade (8) (J) Lampholder (8) (K) Arm-A (4) (L) Arm-B (4) (M) Base (1) (N) Connection terminal (1) (O) LED driving (1)
ACCESSORIES & QTY ENCLOSED: (A) Plastic wire connector (3) (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
3 » Unscrew studs (E) from canopy (F).
Remove mounting plate (C).
Page: – 2 – / 4
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST 4 » Adjust arms to proper position (be like 45° angle)
as shown in the picture.
5 » 1) Screw canopy (F) to the top of tubes (H) and
then screw the unit to the top of base (M). 2) Screw lampshades (I) to the top of lampholders
(J) as shown in the illustration.
6 » · Please wire up the LED Driving first as shown in
the illustration.
7 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
A
B
Connect wires according to the below chart
Connect Black or Red Supply Wire to:
Connect White Supply Wire to:
OUTLET BOX GROUND GREEN GROUND SCREW
OUTLET BOX GROUND
FIXTURE GROUND
DIMPLES
GREEN GROUND SCREW
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
FIXTURE GROUND
Clear, Brown, Gold or Black without tracer
Insulated wire(other than green) with copper conductor
Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with silver conductor
CUPPED WASHER
* Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Neutral Wire
Page: – 3 – / 4
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
· Twist wires together with plastic wire connectors until tightly joined. · Wrap each connector with approved electrical tape. · Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
8 » Attach mounting plate (C) to the outlet box with
mounting screws (B).
9 » Raise canopy (F) to the ceiling and secure canopy
(F) in place by tightening studs (E) onto the preassembled screws in mounting plate (C).
10 » Check everything is already installed properly,
then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Page: – 4 – / 4
