JYL7900A Amoros 27.25 Inch 8-Light Modern Mid-Century Iron LED Chandelier
Product Information
The product is a lighting fixture that requires installation by
a licensed electrician. The item comes with a mounting bracket (A),
green ground screw (B), outlet box screw (C), wire nut (D), plain
washer (J), sleeves (K, O), longer stem (L), fixture body (M),
canopy unit (E), shorter stem (N), 6 rod (F), 12 rod (G), knurled
nut (H), metal cup (I), decorative finial (P), and light bulb (Q).
The product dimensions are 27.25W x34-64H.
Product Usage Instructions
- Switch off the main electrical supply from the main fuse
box/circuit breaker before installation. - Inspect the item carefully before attempting to install. If
there is any damage or obvious defect, do not install. The item may
not be returned once it has been installed. - Make sure that you have all parts indicated before you begin
assembly of this item. The estimated assembly time is 20
minutes. - Attach the mounting bracket (A) to the junction box with outlet
box screw (C). - Spread the arms on the fixture body (M) and adjust them to a
proper position. - Raise the long stem (L) thread to the fixture body (M), then
install the sleeves (K), plain washer (J), and metal cup (I).
Finally, secure with knurled nut (H). - Connect the hot, black or red outlet supply wire to the
parallel cord (round & smooth) and connect the neutral, white
outlet supply wire to the parallel cord (square & ridged).
Connect the clear, brown, gold or black without tracer (colored
stripes) and clear, brown, gold or black with tracer (colored
stripes) insulated wires (not green) with copper metal conductor
and silver metal conductor, respectively. - For installation in the United States, wrap the ground wire
from the outlet box around the green ground screw (B) on the
mounting bracket, no less than 2 from wire end. Tighten ground
screw. If the fixture is supplied with a ground wire, connect it to
the outlet ground wire with a wire nut. For installation in Canada,
if the fixture is supplied with a ground wire, wrap the ground wire
around the green grounding screw on the mounting bracket and
tighten ground screw. - Connect the 12 rod and 6 rod together, lock it to the knurled
nut (H), attach the swivel (E1) to the 6 rod (F), then connect
wires. - Raise the canopy unit (E) thread to the outlet box screws,
secure with canopy nut (R). - Raise the short stem (N) thread to the fixture body (M) then
install the sleeves (O), secure with decorative finial (P). - Install the light bulb (Q) to the socket.
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean clorth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PIECE DESCRIPTION
A
Mounting bracket
B
Green ground screw
C
Outlet box screw
D
Wire nut
PICTURE QUANTITY PIECE DESCRIPTION
1X
J Plain washer
1X
K
Sleeves
2X
L Longer stem
3X
M Fixture body
PICTURE
QUANTITY 1X 1X 1X 1X
E Canopy unit
1X
N Shorter stem
1X
F
6″ rod
2X
O
Sleeves
1X
G
12″ rod
2X
P
Decorative finial
1X
H Knurled nut
1X
Q
Light bulb
8X
I
Metal cup
1X
R
Canopy nut
2X
1/2
Model#: JYL7900A JYL7900B Product Dimensions: 27.25″W x34″-64″H
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1. Attach the mounting bracket (A) to the junction box with outlet box screw (C).
2. Spread the arms on the fixture body (M), adjust them to a proper position. 3. Raise the long stem (L) thread to the fixture body (M), then install the sleeves (K), plain washer (J) and metal cup (I), finally secure with knurled nut (H).
Connect, Hot, Black or Red Outlet Supply Wire to:
Connect, Neutral, White Outlet Supply Wire to:
Black * Parallel Cord (round & smooth)
White * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw(B) on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire nut. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
4. Connect the 12″ rod and 6″ rod together, lock it to the knurled nut (H), attach the swivel (E1) to the 6″ rod (F), then connect wires.
5. Raise the canopy unit (E) thread to the outlet box screws, secure with canopy nut (R). 6. Raise the short stem (N) thread to the fixture body (M) then install the sleeves (O), secure with decorative finial (P). 7. Install the light bulb (Q) to the socket.
specified on this fixture. Make sure that electrical current is turned off before changing bulbs.
PLEASE USE TYPE”B” BULB MAX 25-WATT OR CFL BULB MAX 9-WATT OR LED BULB MAX 5-WATT, THERE IS LED 4-WATT BULB IN THE BOX
ENJOY YOUR LAMP
2/2
