Mountup Mu0015 Tv Wall Mount Full Motion Instruction Manual

• Please read the instruction carefully before installation.
• If you have any doubts about the safety of the installation,
  assembly, or use of this product, please contact us.
• This product is designed for use in wood stud or solid concrete
  wall. DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of
  the TV and mount combined. Incorrect installation may result in
  product damage or body injury.
• WARNING: This product contains small items that could be a
  choking hazard if swallowed.
• Before starting assembly, verify all parts are included and
  undamaged. For parts shortage or damage, please contact us.

• Make sure the TV size is within the maximum limits: 800mm/31.5
  (width) and 400mm/16 (height).
• Ensure that the weight of the TV does not exceed 154LBS
  (70KG).

INSTALLATION INSTRUCTION
V3

Velcro cable ties X5

Bubble level X1

Mounting template X1

Max: 154LBS (70KG)

Max:800x400mm /31.5×16″ Min:200x100mm /8×4″

If you have any questions, please feel free to contact us via Amazon. Warm Tips You could also refer to the Video Guide about installation on our product page.
Step 1-1 Select TV screw diameter

680-84-MU

Thread screws by hand into the threaded holes on the back of your TV to select which screw diameter fits your TV.

M4 M6 M8

Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
This product is designed for use in wood stud or solid concrete wall. – DO NOT install into drywall alone.
The wall must be capable of supporting five times the weight of the TV and mount combined. Incorrect installation may result in product damage or body injury.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage, please contact us.
Must Check Before Getting Started

MAX:800mm/31.5″
MAX: 400mm/16″

Max: 154LBS (70KG)

<16mm(5/8″)

Min. Wood Stud Size: nominal 4″(102mm) actual 3 1/2″(89mm)
Min. Wood Stud Size: nominal 2″(51mm) actual 1 1/2″(38mm)
24″(601mm)

Min. 8″ (203mm)

Drywall with wood studs

Solid concrete wall

CAUTION: DO NOT install into drywall alone.

Installation Tools (Not Included)

Wood Stud Installation Concrete Installation

7/32″ (5.5mm)

Stud Awl Wood

Finder

Drill Bit

3/8″ (10mm)
Masonry Hammer Drill Bit

Step 1-3 Attach the bracket

2M
Band Tape

Pencil

Electrodrill

1/2″ (13mm)
Socket Screwdriver Wrench
1

CAUTION: Ensure bracket is securely fastened before moving on to the next step.

(a) For Flat Back
No!

04
Top of TV

M-A M-C M-B
Use the shorter screws
M-E Not for M8 screws

Hardware Included
Wall Bracket

Front Support

01 x1
End Cap

02 x1
Vertical Brackets

Wrench

03 x2

04 x2

Hardware cWall /Product)

Lag Bolts 5/16 x 3½ in

Washer Ø8mm Open-end wrench

x4

x4

x1

A

B

C

TV Screws / Washers

Philips Screws M4 x 12mm M4 x 30mm

Philips Screws M6 x 15mm M6 x 30mm

Philips Screws M8 x 25mm M8 x 45mm

Spacers L10mm

05 x1

Washers Ø6mm M4-5-6

Spacers L5mm

x4 x4

x4 x4 x4 x4

x8

x4

M-A

M-B

M-C

M-D

M-E

Step 2A Wall plate installation (wood stud)

A-1

x8
M-F
2

16″~24″

Locate your studs. Verify and mark the center of the studs by finding the stud edges using an awl, a thin nail, and an edge-to-edge stud finder.

Step 1-2 Select TV screw length
When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.

(b) For Round Back / Extra Space

No!

Too Short

Too Long

Correct

Correct

04
Top of TV

3

A-2
M-A M-C M-B
Use the longer screws M-E
Not for M8 screws M-D M-F
4

Bubble Level Mounting template

Position the mounting template at your desired height and line up the holes with your stud center line. Level the mounting template and mark the pilot hole locations.
V2

5

2 2

A-3
2.75in (70 mm)
Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.

7/32 in Ø5.5 mm

Step 2B Wall plate installation (concrete or brick)

B-1
Position the mounting template at your desired height , level the mounting template and mark the pilot hole locations x4.

Bubble Level

IMPORTANT: Pilot holes must be drilled to a depth
of 2 3/4 in (70 mm). Be sure to drill into the center of the stud.
A-4
B A
01

Install wall bracket [[00211]] using lag bolts A and washers B . Tighten the lag bolts A until they are pulled firmly against the wall bracket [021]]

B-2

Mounting template
Ø 10 mm

B-3

Concrete wall anchor 4pcs (NOT INCLUDED)

Ø10*61mm
Contact us to have these additional pieces shipped directly to you.

B A No!
V2

To prevent the TV falling down, the Arrow Must Keep UP at this step!!

05
Use the included wrench 05 when have not socket wrench in hand.

Install wall plate 01 using lag bolts A and anchor (not included). Tighten the lag bolts A until they are pulled firmly against the wall plate 01
STEP 3 Install front support and wall bracket together 3-1 Install the End Caps [0033] to Front Support [02] with the preassembled screws.

3/8in Ø 10 mm

05

To prevent the TV falling down, the Arrow Must Keep UP at this step!!

Use the included wrench 05 when have not socket wrench in hand.

No!
6

Drill pilot holes

3.8in 95 mm

7

03

Pre-assembled screws

02

8

STEP 3 Install front support and wall bracket together

Adjustments

Product dimensions:

Max 400mm(15.7″) Min 100mm(4″)

3-2

Hang front support onto wall bracket and using a screwdriver to secure with preassembled screws [PP1] and washer [P22] .

02

P2

01

Tool-free Tilting Adjustment
-10° +5°

(Tilting)
Tilting Angle Adjustment (+5° / -10°) Loosen 2 tilting bolts, pull TV to your desired angle, then fasten tilting nuts with open-end wrench.
Tighten

Max 800mm(31.5″) Min 200mm(8″)

-3°/+3°

P1

Loosen

STEP 4 Hang TV with brackets onto the arm extensions

4-1

04 4-2

4-3

Adjustments TV leveling adjustment (-3°/+3°)
±3°
± 3°

174mm(6.9″)

610mm(24″) 457mm(18″) 406mm(16″) 305mm(12″) 254mm(10″)

P3
Remove the preassembled screws [P33] and save to use, then raise the safety locks.

02 Lift and hang the TV

1 1

Loosen

Press the safety locks then fasten

the removed screws [PP33].

9

Loosen 2 leveling bolts on the rear of TV plate with the open- end wrench C , adjust to level, and retighten to secure.

Max 609mm (24″) Min 73mm (2.9″)
+5°

Tighten

-10°
10

666mm(26.2″)
-45°/+45°
11