Metra 95-7427b Dash Kit Instruction Manual

95-7427B Dash Kit

Product Information

Product Usage Instructions

1. Unclip and remove the panel above the radio including the a/c
   vents and the climate controls. Unplug and remove the panel.
   (Figure A)
2. Unclip and remove the panel below the radio. (Figure B)
3. Remove (6) Phillips screws securing the radio. Unplug and
   remove the radio. (Figure C)
4. Remove (4) Torx head screws securing each side bracket to the
   factory radio. Slightly loosen (1) Torx head screw from each side
   of the module below the radio, and then remove just the radio.
   Retain the brackets and module for re-use during kit assembly.
   (Figure D)
5. Attach the factory brackets and module removed from disassembly
   to the aftermarket radio with the screws supplied with the radio.
   Tighten the (2) Torx head screws to the module that were loosened
   in disassembly. (Figure A)
6. Locate the factory wiring harness and antenna plug in the dash
   and make all necessary connections to the radio. Metra recommends
   using the proper mating adapters from Metra and/or AXXESS.
   Re-connect the negative battery terminal and test the radio for
   proper operation.
7. Mount the new radio assembly into the dash and reassemble the
   dash in reverse order of disassembly.

Technical Support

If you are having difficulties with the installation of this
product, please call our Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a second time, and make
sure the installation was performed exactly as the instructions are
stated. Please have the vehicle apart and ready to perform
troubleshooting steps before calling.

Installer Institute

Enhance your installation and fabrication skills by enrolling in
the most recognized and respected mobile electronics school in our
industry. Log onto www.installerinstitute.com
or call 800-354-6782 for more information and take steps toward a
better tomorrow.

Certified Technicians

Metra recommends MECP certified technicians.

Installation instructions for part 95-7427

Nissan Maxima 2009-2014
(w/o Navigation or Technology Package)
95-7427
KIT FEATURES · ISO DDIN radio provision · PAINTED TO MATCH FACTORY DASH:
95-7427B=BLACK, 95-7427G=GRAY · Textured To Match Factory Dash
KIT COMPONENTS · A) Double DIN radio housing
A

Table of Contents
Dash Disassembly …………………………………………. 2 Kit Assembly ­ ISO DDIN radio provision ……………………………….. 3

REV. 7/16/2015 INST95-7427

WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: · 70-7552 Antenna Adapter: · 40-NI12 TOOLS REQUIRED · Torx screwdriver · Panel removal tool · Phillips screwdriver
METRA. The World’s best kits.TM

metraonline.com

CAUTION! Metra recommends disconnecting the negative bat-
tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership for more information. All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before reconnecting the battery or cycling the ignition. Also, do not remove the factory radio with the key in the on position, or the vehicle running. It would be best to remove the key from the ignition and then wait a few seconds before removing the factory radio.
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

1. Unclip and remove the panel above the radio including the a/c vents and the climate controls. Unplug and remove the panel. (Figure A)
2. Unclip and remove the panel below the radio. (Figure B)

(Figure A)

95-7427

Dash Disassembly

X PASS AIR BAG
OFF

CD CHANGER

AUX IN

3. Remove (6) Phillips screws securing the radio. Unplug and remove the radio. (Figure C)
4. Remove (4) Torx head screws securing each side bracket to the factory radio. Slightly loosen (1) Torx head screw from each side of the module below the radio, and then remove just the radio. Retain the brackets and module for re-use during kit assembly. (Figure D)
Continue to kit assembly

(Figure C)

(Figure B)
2

(Figure D)

ISO DDIN radio provision
1. Attach the factory brackets and module removed from disassembly to the aftermarket radio with the screws supplied with the radio. Tighten the (2) Torx head screws to the module that were loosened in disassembly. (Figure A)
2. Locate the factory wiring harness and antenna plug in the dash and make all necessary connections to the radio. Metra recommends using the proper mating adapters from Metra and/or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.
3. Mount the new radio assembly into the dash and reassemble the dash in reverse order of disassembly.

(Figure A)

95-7427
Kit Assembly
3

Installation instructions for part 95-7427

IMPORTANT
If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

REV. 7/16/2015 INST95-7427

METRA. The World’s best kits.TM

metraonline.com

Metra recommends MECP certified technicians
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

References

• Metra Online | Welcome to Metra Auto Parts Online Warehouse
• Installer Institute | Car Audio Installation and Mobile Electronics Education