2675-695 Ricochet 5-Light Soft Brass Contemporary Pendant
Product Information
The Item#2675-695 is a new fixture that can be installed with
the help of the following instructions. The product includes
mounting plate hardware, ground screw, mounting screw, all thread,
canopy, glass panels, metal frame, tabs, plastic sleeve, candle
covers, and candelabra base bulbs up to 60 watts each or CFL or LED
equivalent (not included).
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting plate hardware. - Carefully unpack your new fixture and lay out all the parts in
a clean area. Take care not to misplace any small parts necessary
for installation. - Determine the desired hanging height and thread rods (F1, F2
and F3) to all thread (G) on the fixture body. Attach canopy (D) by
screwing onto rod (F1). Carefully pass the wires through each rod
during assembly. - Attach the mounting plate (A) to the junction box with mounting
screws (B) (Size: #8-32N*L0.5). The side of the mounting plate (A)
with GND marked on it and two convex points must face out. - Connect the electrical wires as shown in fig 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly
to the mounting plate (A) using the green screw provided. - Tuck wire connectors neatly into the junction box.
- Place canopy (D) over mounting plate (A) and secure with screws
(E). - Install glass panels (J) into metal frame (K) and glass panels
(O) into metal frame (P), then secure with tabs and plastic sleeve
provided. - Align metal frame (K) and metal frame (P) to the holes on
fixture body and secure with screws (M). - Place candle covers (I) over sockets (N).
- Install (5) five candelabra base bulbs (H) up to 60 watts each
or CFL or LED equivalent (not included) in accordance with the
fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE
RATING! - Turn on power and test the fixture.
INSTALLATION INSTRUCTIONS
Item#2675-695 (New. 2022/04/18) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig.1)
Fig. 1
1. Shut off power at the fuse box or circuit breaker box Set#A-021-118DH
and remove the old fixture including the mounting -Mounting plate
hardware.
-Ground screw
2. Carefully unpack your new fixture and lay out all the -Mounting screw*2
parts in a clean area. Take care not to misplace any
A
small parts necessary for installation.
B
ASSEMBLING THE FIXTURE (Fig. 1) 3. Determine the desired hanging height and thread rods
D
(F1, F2 and F3) to all thread (G) on the fixture body. Attach canopy (D) by screwing onto rod (F1). Carefully pass the wires through each rod during assembly. 4. Attach the mounting plate (A) to the junction box (not
E F1
H
included) with mounting screws (B) (Size: #8-32N*L0.5″). The side of the mounting plate (A) with
I
“GND” marked on it and two convex points must face
out.
CONNECTING THE WIRES (Fig. 2) 5. Connect the electrical wires as shown in fig 2, making
sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper),
F2
F3 M
O J
P K
connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the
G N
mounting plate (A) using the green screw provided.
6. Tuck wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
7. Place canopy (D) over mounting plate (A) and secure
with screws (E).
8. Install glass panels (J) into metal frame (K) and glass
panels (O) into metal frame (P), then secure with tabs
and plastic sleeve provided.
9. Align metal frame (K) and metal frame (P) to the holes
on fixture body and secure with screws (M).
10. Place candle covers (I) over sockets (N).
11. Install (5) five candelabra base bulbs (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
Rod# W30-1-695*1(F1) W30-1-695 *2(F2) W30-H-695 *1(F3)
Candle cover# CCV21058P-695
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Fig. 2 FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
FIXTURE WIRES Bare Copper (Ground) HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page: 1/1
LA-3565E
