STAND-V155C Single Wide Screen TV Desk Mount
Product Information:
The Single Wide Screen TV Desk Mount (SKU: STAND-V155C) is a
product designed to mount a flat or curved screen monitor on a
desk. The product is compatible with screens that have VESA
patterns ranging from 75x75mm up to 400x400mm. The product comes
with a pole, clamp, VESA plate, arms, screws, and other hardware.
The product can support a weight of up to 66lbs (29.94kg).
Product Usage Instructions:
- Place the pole cap onto the pole. Ensure that the weight
capacity of the product is not exceeded. - If you are using a clamp installation, slide the cable
management clip and decorative cover onto the pole. Thread the pole
into the base of the clamp until snug, then back off until the
mounting holes are facing forward. Tighten grub screws with an
allen wrench as shown in the diagram. Apply rubber pads as shown in
the diagram and secure the clamp to the desk. - If you are using a VESA plate installation, attach arms L and M
to the VESA plate with screws as per the pattern of your screen
size. If your screen size is 75x75mm up to and including 200x200mm,
use the VESA plate only and do not use arms L and M. Refer to the
diagram for clarification. - If you have a flat back monitor, attach the VESA plate to the
back of the TV with screws and washers. Make sure the two keyholes
on the back have the small end facing up. For curved back monitors,
attach the VESA plate to the back of the TV using screws, washers,
and spacers depending on your TV’s requirements. Refer to the
diagram for clarification. - Insert bolts into the pole at the desired height, making sure
there are three holes unused between bolts. Thread nuts onto bolts
leaving 3mm of thread exposed behind bolt heads. Hang VESA plate
with TV onto bolts and tighten with an allen wrench and
wrench. - Store allen wrenches in the cable clip as shown in the
diagram.
Single Wide Screen TV Desk Mount
Instruction Manual
SKU: STAND-V155C
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-v155c
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
www.vivo-us.com Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER: · NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND. · USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1) VESA Plate
B (x1) Pole
C (x1) Pole Cap
D (x1) Clamp
E (x1) Cable Clip
F (x1) Decorative
Cover
G (x1) Grommet Base
Plate
H (x5) Rubber Pad
I (x1) Grommet Plate
J (x1) 3mm Allen
Wrench
K (x1) 4mm Allen
Wrench
L (x2) Arm
M (x2) Arm
N (x8) Screw
O (x2) Bolt
P (x2) Nut
Q (x1) Wrench
M-A (x4) M5x14
M-B (x4) M6x14
M-C (x4) M6x30
M-D (x4) M8x30
M-E (x4) M8x50
M-F (x4) D5 Washer
M-G (x4) D8 Washer
M-H (x8) D8 Washer
2
M-I (x8) Spacer
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
TOOLS NEEDED
Phillips Screwdriver
ASSEMBLY STEPS
STEP 1
Place pole cap (C) onto pole (B). B
DO NOT EXCEED WEIGHT CAPACITY.
66lbs Failure to do so may result in serious injury. (29.94kg) C
STEP 2
OPTION A: Clamp Installation Slide cable management clip (E) and decorative cover (F) onto pole (B). Thread pole (B) into base of clamp (D) until snug, then back off until the mounting holes are facing forward. Tighten grub screws with allen wrench (J) as shown in diagram. Slide decorative cover (F) down. Apply rubber pads (H) as shown in diagram. Secure clamp (D) to desk.
B
H
J
E F
D
10-88mm
3
STEP 2 (Continued)
OPTION B: Grommet Base Installation Remove screw and plate from clamp (D) as shown in diagram. Apply rubber pads (H) to the bottom of grommet base (G) as shown in diagram. Slide cable management clip (E) and decorative cover (F) onto pole (B). Thread pole (B) into grommet plate (G) until snug, then back off until the mounting holes are facing forward. Tighten grub screws with allen wrench (J) as shown in diagram. Slide decorative cover (F) down. Slide grommet plate (I) onto hand crank. Insert hand crank through grommet hole from bottom and into grommet base (G).
D
G
H
B E F
I
J 10-80mm
STEP 3
75x75mm up to and including 200x200mm Pattern: Arms (L, M) will not be used. Follow diagram below to see which holes to use VESA Plate (A).
A
75x75mm
200x100mm 100x100mm
200x200mm
4
STEP 3 (Continued)
300x300mm or 400x400mm Pattern: Attach arm (L, M) to VESA Plate (A) with screws (N) as shown in the diagram.
N L
M
A
M
300×300 L
400×400
STEP 3 (Continued)
300x200mm or 400x200mm Pattern: Attach arm (L, M) to VESA Plate (A) with screws (N) as shown in the diagram.
N
L A M
M L
300×200 400×200
STEP 4
OPTION A: Flat Back Monitor Attach VESA plate (A) to back of TV with screws (M-A, M-B) and washers (M-F, M-G). Make sure the two keyholes on back have the small end facing up.
M- A M- B M- F M- G
5
STEP 4 (Continued)
OPTION B: Curved Back Monitor Attach VESA plate (A) to back of TV using screws (M-C, M-D, M-E), washers (M-G), and spacers (M-H, M-I) depending on your TV’s requirements as shown in diagrams. Make sure the two keyholes on back have the small end facing up.
M- C M- D
M- G
M- C M- D
M- G
M- C M- D M- G
M- H
M- I
M- H M- I
M- E M- G
M- I
M- E M- G
M- H M- I
M- E M- G
M- H M- I
STEP 5
Insert bolts (O) into pole (B) at desired height, making sure there are 3 holes unused between bolts. Thread nuts (P) onto bolts leaving 3mm of thread exposed behind bolt heads. Hang VESA plate (A) with TV onto bolts, and tighten with 4mm Allen wrench (K) and wrench (Q).
P Q
O K
105mm
3mm
Q K
6
STEP 6
Store allen wrenches (J, K) in cable clip (E) as shown in diagram.
K J
STEP 7
Manage cables using cable clip (E). Loosen the nuts on VESA Plate (A) using Wrench (Q) to adjust the tilt.
±50° +15° -15°
7
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 06/08/2022 REV1.3
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
