65W DALI DT6 NFC Enabled LED Driver
Product Information
The 65W DALI DT6 NFC Enabled LED Driver is a constant current
LED driver that supports DALI signal input. It is designed for use
with LED lighting fixtures and provides accurate current output.
The driver has a rated power of 65W and operates within a wide
input voltage range. It features a dimming interface for
controlling the brightness of the connected LEDs.
The LED driver is equipped with various protection features,
including short circuit protection, over current protection, and
over temperature protection. It has a working temperature range of
-25°C to +45°C and can withstand a maximum case temperature of
85°C. The driver meets safety standards such as EN61347-1 and
EN61347-2-13, as well as EMC standards like EN55015 and
EN61000-3-2.
With NFC programming devices, the LED driver can be easily
configured using the SR NFC Tool app. The app allows users to set
parameters and save configurations via NFC communication. The LED
driver can also be operated with a DALI master controller, which
automatically assigns DALI addresses for channel outputs.
Product Usage Instructions
- Using the LED driver with a DALI master controller:
- Ensure that the wiring is done correctly and power on the DALI
system. - Refer to the user manuals of compatible DALI masters for
specific operations.
- Ensure that the wiring is done correctly and power on the DALI
- Using the LED driver with NFC programming devices:
- Follow the wiring diagram provided.
- Power on the DALI devices after setting the parameters using
the SR NFC Tool app. - To use the SR NFC Tool app:
- Download the app from the App Store or Google Play by searching
for “SR NFC Tool”. - Open the app and tap “+” to add DALI devices.
- Make sure your mobile phone has NFC function enabled.
- Add the LED driver device and give it a name.
- Unlock the device to access the parameters configuring
page. - Select the desired settings based on your requirements.
- Save the selected configuration via NFC and power on the
device.
- Download the app from the App Store or Google Play by searching
Wiring Diagram
1. With DALI bus:
LED OUTPUT LED DALI Bus L N INPUT DALI INPUT - DALI Dimmable Driver DA DA L N
2. With PUSH dimmer:
LED OUTPUT LED DALI Bus L N INPUT DALI INPUT - DALI Dimmable Driver DA DA L N
65W DALI DT6 NFC Enabled LED Driver(Constant Current)
2
Important: Read All Instructions Prior to Installation Function introduction
LED OUTPUT
LED Output –
DALI signal input AC Push input
AC/DC power input
Product Data
LED Channel
DC Voltage
Output
Current Current Accuracy
Rated Power
Input
Voltage Range Frequency Range
Power Factor (Typ.) Total Harmonic Distortion Efficiency (Typ.)
AC Current (Typ.) Inrush Current (Typ.)
Leakage Current
Standby Power Consumption
Anti Surge
Dimming Interface
Control
Dimming Range Dimming Method
Dimming Curve
INPUT
DALI INPUT
DALI Dimmable Driver
DA DA L N
1 6-58V 500-1500mA via NFC setting; Min.current gear lower to 0.1mA ±3%( ±1%@Certain full load) @ full load Max. 65W 200-240VAC/176-280VDC 0/50/60Hz > 0.98 @ 230VAC Full load THD 6% (@ full load / 230VAC) 90% @ 230VAC full load 0.35A @ 230VAC Max. 9.68A at 230VAC; 70s duration < 5mA /230VAC 0.5W L-N:2KV DALI Device Type 6 (DALI consumption < 2mA)/ AC Push 0.01%-100%@ Max current Amplitude/CCR dimming Linear/ Logarithmic optional
Short Circuit
Yes, recovers automatically after fault condition is removed
Protection
Over Current
Yes, recovers automatically after fault condition is removed
Over Temperature
Yes, recovers automatically after temperature drop
Working Temp.
-25 ~ +45
Max. Case Temp. Environment
Working Humidity
Storage Temp. & Humidity
Safety Standards
TC=85 (Ta=”45″) 10% ~ 95% RH non-condensing -40 ~ +80, 10% ~ 95% RH
EN61347-1, EN61347-2-13
Safety & EMC
Withstand Voltage Isolation Resistance
EMC Emission
I/P-O/P: 3.75KVAC I/P-O/P: 100M Ohms / 500VDC / 25 / 70% RH
En55015, EN61000-3-2, EN61000-3-3
EMC Immunity
En61547, EN61000-4-2,3,4,5,6,8,11
Others
MTBF
Dimension Warranty
191350H, MIL-HDBK-217F @ 230VAC full load and 25 ambient temperature
123.9×78.8x30mm (L*W*H) 5 Years
· In compliance with IEC 62386-101:2014, IEC 62386-102:2014, IEC 62386-207 Ed2 · Built-in DALI-2 interface, DALI DT6 device · Dimmable LED driver. Max. output power 65W · 500-1500mA current selectable via NFC program tool. Min.current gear lower to 0.1mA · DALI Address/Group/Scene setting via NFC program tool. · Class power supply, full isolated plastic case · High power factor and efficiency · To switch and dim LED lighting luminaries · Amplitude/CCR dimming, smooth and deep dimming · Compatible with universal DALI masters that support DT6 commands · Error report function · IP20 rating, suitable for indoor LED lighting applications · 5 years warranty
Safety & Warnings
· DO NOT install with power applied to the device. · DO NOT expose the device to moisture.
Operation
With DALI master
1. DALI Address 1 DALI address for 1 channel output are assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations.
With NFC Programming devices Note 1) Do wiring according to the wiring diagram and power on the DALI system . 2) Recommend setting parameters without power-on the DALI devices . 2) Please make sure your mobile phone has NFC function and enable it . Working with “SR NFC Tool” APP Step 1: Download the APP (searching “SR NFC Tool” from App Store and Google Play) .
Then open the APP .
Tap “+” to add DALI devices
Download “SR NFC Tool ”
Note: 1. Please Make sure that you have enabled NFC function with your mobile phone/ tablet . 2. Please Make sure that the “NFC position” is matched. 3. Please do not power on the device before setting. 4. If you can’t download “SR NFC Tool”. Please contact with us.
Step 2: Add device, and name it as you wish.
Step 3: Unlock device, enter parameters configuring page.
Locked
Unlock it
Note: 1. You have to unlock the device then do some settings 2. Only when the corresponding function is selected, the function interface will be displayed.
Step 4: Few parameter interface, you can choose the setting based on your requirements.
Step 5: After setting, please save the selected configuration via NFC and power on the device.
Tips
1. NFC function doesn’t require any power driver. 2. Many functions can be configured by NFC. Kindly check your desired functions. 3. All of our DALI drivers are in the best performance within our DALI master/ gateway.
Wiring Diagram
1. With DALI bus 1With single color LED luminarie
LED OUTPUT
LED
DALI Bus
L N
INPUT
DALI INPUT
–
DALI Dimmable Driver
DA DA L N
2. With PUSH dimmer
LED OUTPUT
LED
AC PUSH SWITCH
LN
INPUT
DALI INPUT
–
DALI Dimmable Driver
DA DA L N
AC Push Function
1) Click the button to switch ON/OFF 2) Press and hold down the button to increase or decrease light intensity to desired level and release it, then repeat the operation to adjust light intensity to opposite direction. The dimming range is from 1% to 100%.
Product Dimension
Operating window
60
ULED (max), V
54
Output voltage [V]
45
36
ULED (min), V
27
18
9
0 0,10 0,30 0,50 0,70 0,90 1,10 1,30 1,50 1,70 Output current [A] Dimming Curve
Note: Test data under 1500mA gear
Driver Performance
Note: Test data under 1500mA gear
Driver Performance
Note: Test data under 1500mA gear
MCB Load Quantity
Module Number
Ipeak Twidth
Max.quantity of LED Driver per MCB
B10 B13 B16 B20 B25 C10 C13 C16 C20 C25 D10 D13 D16 D20 D25
SRP-2305N-65CC500-1500 9.68A 70s 15 20 24 30 38 20 26 32 40 50 22 29 36 45 57
SRP-2309N-65CCT500-1500 9.68A 70s 15 20 24 30 38 20 26 32 40 50 22 29 36 45 57
I (A) Ipeak ½ Ipeak
t
T (ms)
Note:
1.Those MCB parameters are based on ABB S200 series circuit breakers.
2.For different brands and models of miniature circuit breakers, the quantity of drivers will have difference.
3.Please do not exceed the above-mentioned quantity during on-site installation, and the specific load quantity shall be subject to on-site installation.
4.When the installation environment temperature of MCBs exceeds 30°C or when multiple MCBs are installed side by side, the number of mounted drives will be reduced, which requires recalculation.
5.Type C MCB’s are strongly recommended to use with LED lighting
Update log
Date 2022-9-9
Version V1.0
Update content Initial Version
NoteSubject to change without notice. Please contact us if you have any questions.
Update by Romeo
