Bega 24737 Wall Luminaire Instruction Manual (+ PDF)

24 737
Wall luminaire
IP 65

Contents hide

1 Instructions for use

2 Safety

3 Installation

4 Cleaning · Maintenance

5 Spares

6 Documents / Resources

6.1 References

7 Related Posts

Instructions for use

Application
Wall luminaire with single-sided light output for illumination and design tasks in architecture.
The luminaire can be installed with the light distribution opening upwards or downwards.
Product description
Luminaire made of aluminium alloy, aluminium and stainless steel BEGA Unidure® coating technology Colour graphite, silver or white Matt safety glass Reflector surface made of pure aluminium Mounting plate with 2 elongated holes Width 4.4 mm · Spacing 62 x 95 mm 2 cable entries for through-wiring of mains supply cable ø 7-12 mm Connecting terminal 2.5@ with plug connection Earth conductor connection LED power supply unit 220-240 V x 0/50-60 Hz BEGA Thermal Control® Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire Safety class I
Protection class IP 65
Dust-tight and protection against water jets Impact strength IK05
Protection against mechanical impacts < 0.7 joule
– Conformity mark
Weight: 2.6 kg
This product contains light sources of energy efficiency class(es) C, D

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Light technique
Broad spread light distribution.
Half beam angle 72°

Lamp

Module connected wattage	8.4 W
Luminaire connected wattage	10 W
Rated temperature	ta = 25 °C
Ambient temperature	ta max = 60 °C
24 737 K3
Module designation	LED-1145/830
Colour temperature	3000 K
Colour rendering index	CRI > 80
Module luminous flux	1480 lm
Luminaire luminous flux	1045 lm
Luminaire luminous efficiency	104,5 lm / W
24 737 K4
Module designation	LED-1145/840
Colour temperature	4000 K
Colour rendering index	CRI > 80
Module luminous flux	1555 lm
Luminaire luminous flux	1098 lm
Luminaire luminous efficiency	109,8 lm / W

Overvoltage protection
The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components. You can find them on our website at www.bega.com.

Installation

Undo hexagon socket head screws (wrench size 3 mm) up to the stop and disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Make earth conductor connection and electrical connection to the connecting terminal (plug connection).
Push plug into coupler as far as it will go.
Place luminaire housing onto the mounting plate and fix it.
Make sure that gasket is positioned correctly.

Cleaning · Maintenance

Clean luminaire regularly with solvent-free
cleansers from dirt and deposits.
Do not use high pressure cleaners.

Please note:
Do not remove the desiccant bag from the luminaire housing.
It is needed to remove residual moisture.

Replacing the LED module
The designation of the LED module is noted on a label in the luminaire.
The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted.
The module can be replaced by qualified persons using standard tools.
Disconnect the system and open the luminaire.
Please follow the installation instructions for the LED module.
Inspect and, if necessary, replace the luminaire gaskets.
Defective glass must be replaced.
Close the luminaire.