MOUNT-CAR01 Car Laptop Mount
Product Information: Car Laptop Mount
The Car Laptop Mount is a device that allows you to securely
mount your laptop on the passenger seat of your car. It comes with
a base, pole, arm, laptop tray, knobs, cable clips, support screw,
connecting bracket, Velcro strap, strap brackets, lower and upper
laptop arms, screw cap, M6x10mm screws, M6 washers, M6 nuts,
M5x10mm screws, M5 nuts, M5x6mm screws, M4x5mm thumbscrew, M4
washer, M6 flanged nut, M6x45mm screw, 5mm Allen wrench and a
regular wrench. The product is designed to hold a maximum weight of
11lbs (5kg) and failure to comply with this weight limit may result
in serious injury.
Product Usage Instructions: Car Laptop Mount
- Identify the foot style needed for your passenger seat
configuration using the images provided in the manual. Install the
compatible foot for your passenger seat’s left bolt to the threads
on the connecting bracket using M6 nuts, M6 washers, and the wrench
provided. - Loosely assemble the right foot assembly to the base using
M6x10mm screws and a Phillips screwdriver. Align the left foot with
the left seat bolt on the passenger seat. Adjust the right foot to
match up with the right bolt on the seat and tighten M6x10mm
screws. - Loosen the front seat bolts on the passenger seat using a
socket wrench. Slide the left foot under the left seat bolt and the
right foot under the right seat bolt. Adjust the placement as
needed and re-tighten bolts. - Attach the pole to the back of the base using knobs. Thread
support screws onto the base and place screw caps onto the ends
once threaded. - Slide the arm onto the pole with the adjustment bolt pointing
up. Tighten and secure with a 5mm Allen wrench. Determine the
desired pole height and insert an M6x45mm screw into the slot.
Secure using an M6 flanged nut, making sure the flanged, wider part
of the nut is facing outward, with the hex side fitting into the
hex indention on the pole. - Secure strap brackets to the laptop tray using M5x6mm screws
and a Phillips screwdriver. Attach lower laptop arms with a tab
pointing up to the underside of the laptop tray using M5x6mm screws
and a Phillips screwdriver. Connect upper laptop arms to the front
tab of lower arms using M4 washers and M4x5mm thumbscrews. - Once everything is securely attached, place your laptop on the
tray and use the Velcro strap to hold it in place. Adjust the arm
and tray as needed for a comfortable viewing angle.
Please note that this product contains small parts and is not
suitable for children under 3 years. Adult supervision is required
during assembly and usage.
Car Laptop Mount
Instruction Manual
SKU: MOUNT-CAR01
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/mount-car01
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
www.vivo-us.com Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1) Base
B (x2) 0° Foot
C (x2) 90° Foot
D (x2) 45° Foot
F (x1) Pole
G (x1) Arm
H (x1) Laptop Tray
I (x4) Knob
J (x2) Cable Clips
K (x2) Support Screw
L (x1) Connecting
Bracket
Q (x1) Velcro Strap
M (x2) Strap Brackets
N (x2) Lower Laptop
Arm
O (x2) Upper Laptop
Arm
P (x2) Screw Cap
S-A (x4) M6x10mm
Screw
S-B (x8) M6 Washer
S-C (x2) M6 Nut
S-D (x4) M5x10mm
Screw
S-E (x4) M5 Nut
S-F (x8) M5x6mm
Screw
S-G (x2) M4x5mm Thumbscrew
S-H (x2) M4 Washer
S-I (x1) M6 Flanged Nut
S-J (x1) M6x45mm
Screw
T-A (x1) 5mm Allen
Wrench
T-B (x1) Wrench
TOOLS NEEDED
NOTE: SOME HARDWARE MAY NOT BE USED
Phillips Screwdriver
2
Socket Wrench
DO NOT EXCEED WEIGHT CAPACITY. 11lbs
Failure to do so may result in serious injury.
(5kg)
ASSEMBLY STEPS
STEP 1
Begin by identifying what foot style is needed for your passenger seat configuration, using the images below. Please note that the two front seat bolts of some vehicles will differ from each other in angle.
0°
90°
45°
Attach the appropriate foot for the passenger seat’s left bolt [ 0° Foot (B), 90° Foot (C), or 45° Foot (D) ] to the left underside of of Base (A) using M6x10mm Screws (S-A) M6 Washers (S-B), and a Phillips screwdriver.
S-A
S-B C
B
0° A
90°
D
45°
Install compatible Foot (B, C, D) for your passenger seat’s left bolt to the threads on Connecting Bracket (L) using M6 Nuts (S-C), M6 Washers (S-B), and Wrench (T-B). Please note, based on your passenger seat’s floor bolts, you may need a different foot than what was used above.
T-B
S-C S-B
B
OR
D C
OR
L
0°
90°
45°
3
STEP 2
Loosely assemble the right foot assembly to Base (A) using M6x10mm Screws (S-A), M6 Washers (S-B), and a Phillips screwdriver. Align the left foot with the left seat bolt on the passenger seat. Adjust the right foot to match up with the right bolt on the seat and tighten M6x10mm Screws (S-A).
S-A S-B A
STEP 3
Loosen the front seat bolts on passenger seat using a socket wrench (size needed depends on manufacturer).
Slide the left foot under the left seat bolt and the right foot under the right seat bolt. Adjust the placement as needed and re-tighten bolts.
4
STEP 4
Attach Pole (F) to back of Base (A) using Knobs (I). F
I
A
STEP 5
Thread Support Screws (K) onto Base (A) and place Screw Caps (P) onto the ends once threaded.
K
A P
5
STEP 6
1. Slide Arm (G) onto Pole (F) with the
adjustment bolt pointing up. Tighten and
G
secure with 5mm Allen Wrench (T-A). Adjust
the swivel using 5mm Allen Wrench.
T-A
F
T-A
2. Determine desired Pole (F) height and
S-I
Insert M6x45mm Screw (S-J) into slot.
Secure using M6 Flanged Nut (S-I), making
sure the flanged, wider part of the nut is
faing outward, with the hex side fitting into
S-J
the hex indention on Pole (F).
STEP 7
Secure Strap Brackets (M) to Laptop Tray (H) using M5x6mm Screws (S-F) and a Phillips Screwdriver.
S-F H
M 6
STEP 8
Attach Lower Laptop Arms (N) with tab pointing up to underside of Laptop Tray (H) using M5x6mm Screws (S-F) and a Phillips screwdriver. Connect Upper Laptop Arms (O) to front tab of Lower Arms (N) using M4 Washers (S-H) and M4x5mm Thumbscrews (S-G).
Note: Lower Laptop Arms (N) installed in the up position is compatibile with laptops 0.5″ to 1.25″ in thickness.
H
O
S-F
S-G
N
S-H
Note: Lower Laptop Arms (N) can be pointed down to allow for thinner laptops (0 to 0.5″) to be used with mount.
STEP 9
Connect Laptop Tray (H) to assembly using M5x10mm Screws (S-D), M5 Nuts (S-E), and a Phillips screwdriver. Use 5mm Allen Wrench (T-A) to adjust the tilt and swivel on VESA bracket. Place Cable Clips (J) on Arm (G) to manage cables. Tighten Support Screws (K) to level the mount.
T-A
T-A
Feed Velcro Strap (Q) through Strap
Brackets (M). Use to secure laptop to tray.
J
M
Q
7
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 03/01/2023 REV1.1
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
