94800826 Tempest Pillar Mount
Product Information
The TempestTM Pillar Mount (sku 94800826) is a mounting kit
designed for the installation of the Tempest gas torch head. It
includes a pillar mount, pillar cover, 16-inch gas flex line, 3/8
to 3/8 flare fitting, 2 8-32 thumb screws, and necessary mounting
hardware.
Compatibility: The pillar mount is compatible with the Tempest
gas torch head.
Packing List:
- Pillar Mount
- Pillar Cover
- 16-inch Gas Flex Line
- 3/8 to 3/8 Flare Fitting
- (2) 8-32 Thumb Screws
Please note that the illustration provided in the manual is for
example purposes only. It is essential to adhere to all gas line
and building code requirements specific to your location. The base
of the pillar mount may need to be shimmed to ensure proper
leveling.
Product Usage Instructions
Suggested Order of Installation:
- Determine a suitable location for the pillar mount.
- Route the gas line to the center of the pillar mount location,
ensuring that the gas inlet is positioned 1 to 2 inches above the
surface. Cap the gas line. It is recommended to perform a leak test
on the gas line at this stage. - Place the pillar mount in the desired location and mark the
four mounting holes. Drill appropriate holes based on the type of
fasteners being used. However, do not secure the pillar mount at
this point. - Slide the included pillar cover and control cover over the
pillar mount. - Attach the included flex tube to the 3/8 to 3/8 flare fitting
and then connect it to the flex tube on the Tempest head. - Route the 24-volt wires through the mount and connect them to
the Tempest head according to the instructions provided in the
Tempest manual. - Position the pillar mount over the marked mounting holes and
secure it in place. - Place the Tempest head over the pillar mount and secure it
using the four screws provided with the Tempest. - Ensure that the flex tube fits tightly within the pillar mount.
It is suggested to create several bends in the tube before
installation. - Attach the control cover and glass on the Tempest as per the
instructions outlined in the Tempest manual.
Please refer to the Tempest manual for more detailed information
on connecting the 24-volt wires and attaching the control cover and
glass.
TempestTM Pillar Mount
(sku 94800826)
Compatibility
This post is for use with the following permanent-mount Tempest models Tempest Torch 24v (LP – 94900755 & NG – 94900745) Tempest Torch Manual Start (LP – 94900753 & NG – 9490043) Tempest Lantern 20k – 24v (LP – 94900757 & NG – 94900747) Tempest Lantern 20k – Manual Start (LP – 94900756 & 94900746) Tempest Lantern 50k – 24v (LP/NG 94900748)
Packing List
Pillar Mount Pillar Cover
16″ Gas Flex Line 3/8″ to 3/8″ Flare Fitting
(2) 8-32 Thumb Screws
Pillar Mount Attachment Tempest Torch & Lantern 20k (for Lantern 50k see next page)
NOTE: The illustration below is for example only. Make sure to follow all gas line and building code requirements for your location. The base may be shimmed to level the mount.
Page 1 of 3
17601540 – 4/13/2022
© Travis Industries, Inc.
TempestTM Pillar Mount
(sku 94800826)
Pillar Mount Attachment Tempest Lantern 50k
NOTE: The illustration below is for example only. Make sure to follow all gas line and building code requirements for your location. The base may be shimmed to level the mount.
Page 2 of 3
17601540 – 4/13/2022
© Travis Industries, Inc.
TempestTM Pillar Mount
(sku 94800826)
Suggested Order of Installation
1. Determine a location for the pillar mount.
2. Route the gas line to the center of pillar mount location, placing the gas inlet 1″ to 2″ above the surface and cap the gas line. You may wish to leak test the gas line at this time.
3. Place the pillar mount in location and mark the four mounting holes. Drill appropriate holes in this location for the type of fasteners being used. Do not secure the pillar mount at this time.
4. Slide the pillar cover (included with this kit) and control cover (included with the torch) over the pillar mount.
5. Attach the flex tube (included with this kit) to the 3/8″ to 3/8″ flare fitting (included with this kit) then attach to the flex tube on the Tempest head.
NOTE: Do not install the glass on the head at this time wait until the Tempest is fully installed before installing the glass. Slide the flex tube through the pillar mount and attach to the gas line. With the flex tube and gas line fully secured, turn on gas to the Tempest and leak test the gas line connections.
6. Route the 24-volt wires through the mount and connect them to the Tempest head (see Tempest manual for details).
7. Position the pillar mount over the mounting holes and secure.
8. Place the head over the pillar mount and secure with the four screws (included with the Tempest).
NOTE: The flex tube may fit very tightly within the pillar mount. We suggest that you place several bends in the tube before installing.
9. Attach the control cover and glass on the Tempest (see the Tempest manual for details).
Page 3 of 3
17601540 – 4/13/2022
© Travis Industries, Inc.
