JYL7592A 34 Inch Pendants Rustic 4 Light Oil Rubbed
Product Information:
Model#: JYL7592A
Product Dimensions: 33.5L X 4.75W X (21-51)H
Estimated Assembly Time: 20 minutes
Part List:
- Mounting bracket – 1X
- Machine screw – 2X
- Lock washer – 1X
- Short threaded rod – 1X
- Ground screw – 1X
- Wire connector – 3X
- Canopy – 1X
- Finial – 1X
- Closable Link – 2X
- Tubes – 1X
- Body – 1X
- Screws – 12X (4X 6 – 4X 12)
- Iron shade – 4X
- Socket ring – 4X
- Bulb – 4X
- Glass shade – 4X
Product Usage Instructions:
- WARNING: We recommend installation of this lighting fixture be
done by a licensed electrician. Switch off the main electrical
supply from the main fuse box/circuit breaker before installation.
Inspect the item carefully before attempting to install. If there
is any damage or obvious defect, do not install. The item may not
be returned once it has been installed. - Before beginning assembly of the product, make sure all parts
are present. Compare parts with the package contents list and
hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product. - Secure the mounting bracket (A) to the outlet box with the
machine screw (B). Insert the lock washer (C) and thread the short
threaded rod (D) onto the mounting bar (A), then secure it with the
nut of the short threaded rod (D). - Connect the tubes (K) together to get the desired length and
fix the bottom end to the nipple of the body (L), and the top end
to the loop (J). Hang the loop (I) on the loop of the canopy
(G). - Connect loops by loop (J) and loop of the canopy (G) with the
closable link (I). - Make wire connections using wire connectors (F) according to
the reference chart provided. Connect the hot black or red outlet
supply wire to the parallel cord (round & smooth) and connect
the neutral white outlet supply wire to the parallel cord (square
& ridged). - Grounding Instructions:
a) For installation in the United States: Wrap the ground wire from
the outlet box around the green ground screw (E) on the mounting
plate, no less than 2 inches from the wire end. Tighten the ground
screw. If the fixture is supplied with a ground wire, connect it to
the outlet ground wire using a wire connector.
b) For installation in Canada: If the fixture is supplied with a
ground wire, wrap the ground wire around the green grounding screw
on the mounting plate and tighten the ground screw. - Orient the ceiling canopy (G) so that the short threaded rod
(D) goes into the holes in the canopy, then secure it with the
provided finial (H). - Put the steel shade (N) on the socket, then fasten it with the
socket ring (O). - Install the bulb (P). Be sure to use light bulb(s) with wattage
no greater than specified on this fixture. Always make sure that
electrical current is turned off before changing bulbs. - Attach the glass shade (Q) to the iron shade (N) and then fix
it using the screws (M).
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this luminaire cannot be replaced If the cord is damaged, the luminaire shall be destroyed
Part List and Hardware List
PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE
A
mounting bracket
1X
J
loop
B machine screw
2X
K
tube
C
lock washer
D
short threaded rod
1X
L
body
1X
M
screws
QUANTITY
2X 12″ – 4X 6″ – 4X
1X
12X
E ground screw
1X
N
iron shade
4X
F wire connector
3X
O
socket ring
4X
G
canopy
1X
P
bulb
4X
H
finial
1X
Q
glass shade
4X
I
closable Link
2X
1/2
Model#: JYL7592A Product Dimensions: 33.5″L X 4.75″W X (21-51″)H
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1.Secure mounting bracket (A) to outlet box with machine screw (B),Insert lock washer (C) and thread the short threaded rod(D) onto mounting bar (A), then secure with the nut of the short threaded rod(D).
2. connect the tubes(K) together to get desired length and fix the bottom end to nipple of the body (L), the top end to the loop (J), and then hang the loop (I) on the loop of the canopy (G)
3.Connect loops by loop(J) and loop of the canopy (G) with the closable link(I).
4. Make wire connections, with wire connectors(F), following the reference chart listed below.
Connect, Hot, Black or Red Outlet Supply Wire to:
Connect, Neutral, White Outlet Supply Wire to:
Black * Parallel Cord (round & smooth)
Clear, Brown, Gold or Black without Tracer stripes)
(colored
White * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw(E) on mounting plate, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting plate. Tighten ground screw.
5. Orient the ceiling canopy(G) so that the short threaded rod(D) into the holes in the canopy, then secure it with the provided finial(H).
6. Put the steel shade(N) on socket,then fasten it by socket ring(O).
7. Install bulb(P). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
8. Attach the glass shade(Q) to the iron shade (N) and then fixed using the screws(M).
PLEASE USE ON/OFF TYPE”A” BULB MAX 25-WATT OR LED BULB MAX 5-WATT THERE ARE LED 4PCS 4WATT BULB IN THE BOX ENJOY YOUR LAMP
2/2
