JCHR35W5C2/C3 Remote Controller
Product Information
The JCHR35W5C2/C3 Remote Controller is a 16-channel LCD remote
controller used for controlling motorized shades. The remote
controller has two models, JCHR35W5C2 and JCHR35W5C3, both of which
have the same number of channels and LCD display. The remote
controller features three favorite positions, where the user can
save their preferred shade positions at 25%, 50%, and 75%.
Models & Parameters
The specific parameters for each model can be found on the
nameplate of the product.
Caution!
1. The transmitter should not be exposed to moisture or impact,
so as not to affect its life. 2. During use, when the remote
control distance is significantly shorter or less sensitive, please
check whether the battery needs to be replaced. 3. When the battery
voltage is too low, the LED screen will show a low voltage prompt,
prompting to replace the battery. 4. Please properly dispose of
used batteries according to the local garbage classification and
recycling policy.
Product Usage Instructions
Channels & Groups Toggling
Note: Channel 0 is the group control for all the channels.
Number of Channels Setting
To set the number of channels, refer to the instructions for
each model.
Number of Groups Setting
To set the number of groups, refer to the instructions for each
model.
Channel in Group Setting
To add or remove a channel from a group, short press the button
corresponding to that channel. If the channel number is steady-lit,
it is part of the group. If the channel number is flashing, it is
not part of the group.
Check the Channels in Groups
Refer to the instructions for each model to check which channels
are in a group.
Prohibit Dual-key Operation
To prohibit dual-key operation, refer to the instructions for
each model.
Position Percent Setting
To set the shade position percentage, stop the shade at the
desired percentage and wait 3 seconds. The shade will move to the
chosen percentage position.
Special operation on remote controller JCHR35W5C3:
- CH+ & Up: Upper limit set
- CH+ & Down: Lower limit set
- CH+ & Stop: Favorite position set
- Press the CH+ button for 2 seconds to fast get to the favorite
position
For all other operations, refer to the motor operation
instruction manual.
JCHR35W5C2/C3 Remote Controller
User Manual
01 Product Info
CH+
CH-
JCHR35W5C2
16-channel LCD remote controller
Fav 1 (25%) Fav 2 (50%) Fav 3 (75%)
JCHR35W5C3
16-channel LCD remote controller
JCHR35W5C2/C3 02 Models & Parameters
(more info please refer to the nameplate)
03 Caution!
1. The transmitter should not be exposed to moisture or impact, so as not to affect its life 2. During use, when the remote control distance is significantly shorter or less sensitive,
please check whether the battery needs to be replaced. 3. When the battery voltage is too low, the LED screen will show a low voltage prompt,
prompting to replace the battery. 4. Please properly dispose of used batteries according to the local garbage classification
and recycling policy.
04 Instructions
a.Channels & Groups Toggling
NoteChannel 0 is the group control for all the channels.
b.Number of Channels Setting
(JCHR35W5C2) (JCHR35W5C3)
c.Number of Groups Setting
(JCHR35W5C2) (JCHR35W5C3)
d.Channel in Group Setting
(JCHR35W5C2) (JCHR35W5C3) Short press , if you want the Channel in the group, the Channel number will be steady-lit. Short press again, if you want the Channel not in the group, the Channel number will be flashing.
e.Check the Channels in Groups
(JCHR35W5C2) (JCHR35W5C3)
pattern f.Prohibit Dual-key Operation
LCD shown a lock icon such as limits setting.
g.Position Percent Setting
Stop on the desired percentage down and wait 3s. The shades will move to the chosen percentage down position.
h.Special operation on remote controller JCHR35W5C3:
CH+ & Up: Upper limit set CH+ & Down: Lower limit set CH+ & Stop: Favorite position set Press the “CH+” button for 2s to fast get to the Fav. point
i.For other operations, please refer to the motor operation instruction
