JYL9926 Honeycomb 7.5 Inch 1-Light Brass Gold-Clear Modern Contemporary Arm-Adjustable Iron-Glass LED Sconce
Product Information
The JYL9926 is a lighting fixture that requires installation by
a licensed electrician. The fixture has a dimension of 7.5”W X
12.75H X 14.5E. The external flexible cable or cord of this lamp
cannot be replaced. If the cord is damaged, the lamp shall be
destroyed. The fixture comes with a mounting bracket, backplate,
shade, nut, machine screws, wire connectors, and an LED bulb. The
maximum wattage for the bulb is 40 watts for type A bulbs, 13 watts
for CFL bulbs, and 9 watts for LED bulbs.
Product Usage Instructions
Before starting the assembly, check if all parts are present. Do
not attempt to assemble the product if any part is missing or
damaged. The estimated assembly time for the fixture is 20
minutes.
To install the fixture:
- Switch off the main electrical supply from the main fuse
box/circuit breaker before installation. - Fix the mounting bracket to the outlet box with machine
screw. - Make wire connections with wire connectors following the
reference chart listed in the instructions. - Orient the backplate so that the holes in the ears on the side
of the mounting bracket are aligned with the holes in the rear
plate, and then secure with machine screws. - Install the bulb. Ensure that you use a light bulb with wattage
no greater than specified on this fixture. Always make sure that
electrical current is turned off before changing bulbs. - Carefully insert the opening of the shade into the bulb and
rotate the nut to secure the shade to the lamp body.
For grounding instructions:
- For installation in the United States: Wrap ground wire from
outlet box around green ground screw on mounting bracket, no less
than 2 from wire end. Tighten ground screw. If fixture is supplied
with a ground wire, connect to outlet ground wire with a wire
connector. - For installation in Canada: If fixture is supplied with ground
wire, wrap ground wire around green grounding screw on mounting
bracket. Tighten ground screw.
Enjoy your new lamp!
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slighly damperned clean clorth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
Model#: JYL9926 Product Dimensions: 7.5”W X 12.75″H X 14.5″E
1/2
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1. Fix the Mounting Bracket(B) to the outlet box with machine Screw(A).
2. Make wire connections, with Wire Connectors(C), following the reference chart listed below.
Connect, Hot, Black or Red Outlet Supply Wire to:
Black * Parallel Cord (round & smooth)
Connect, Neutral, White Outlet Supply Wire to:
White * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
3. Orient the Back Plate (D) so that the holes in the ears on the side of the mounting bracket are aligned with the holes in the rear plate, and then secure with Machine Screws (E).
4. Install Bulb(H). Be sure to use light Bulb(H) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
5. Carefully insert the opening of the Shade (G) into theBulb (H) and rotate the Nut (F) to secure the Shade (G) to the Lamp Body (D)
PLEASUE USE TYPE”A” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED MAX 9-WATT THERE ARE 1 X 4W LED BULBS IN THE BOX.
ENJOY YOUR LAMP
2/2
