Mountup Mu0028-24k Full Motion Tv Wall Mount For 42-70 Inches Tvs Instruction Manual

• Ensure that the TV mounting holes fall within the range of
  maximum dimensions: 600mm/24 (width) and 400mm/16 (height).
• The maximum weight supported by the mount is 100 lbs (45.5
  kg).

If you have any questions or need further assistance, please
feel free to contact us via Amazon. You can also refer to the Video
Guide about installation on our product page for additional
help.

INSTALLATION INSTRUCTION
V4

Velcro cable ties X5

Bubble level X1

Mounting template X1

Max: 100LBS (45.5KG)

Max:600x400mm /24×16″ Min:200x100mm /8×4″

MU-680C-24

If you have any questions, please feel free to contact us via Amazon.
Warm Tips You could also refer to the Video Guide about installation on our product page.

Step 1-1 Select TV screw diameter

Thread screws by hand into the threaded holes on the back of your TV to select which screw diameter fits your TV.

M4 M6 M8

Safety Caution
Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.
This product is designed for use in wood stud or solid concrete wall. – DO NOT install into drywall alone.
The wall must be capable of supporting five times the weight of the TV and mount combined. Incorrect installation may result in product damage or body injury.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage, please contact us.

Must Check Before Getting Started

MAX:600mm/24″
MAX: 400mm/16″

Max: 100LBS (45.5KG)

<16mm(5/8″)

Min. Wood Stud Size: nominal 4″(102mm) actual 3 1/2″(89mm)
Min. Wood Stud Size: nominal 2″(51mm) actual 1 1/2″(38mm)
24″(610mm)

Min. 8″ (203mm)

Drywall with wood studs

Solid concrete wall

CAUTION: DO NOT install into drywall alone.

Installation Tools (Not Included)

Wood Stud Installation Concrete Installation

7/32″ (5.5mm)

Stud Awl Wood

Finder

Drill Bit

3/8″ (10mm)
Masonry Hammer Drill Bit

Step 1-3 Attach the bracket

2M
Band Tape

Pencil

Electrodrill

1/2″ (13mm)
Socket Screwdriver Wrench
1

CAUTION: Ensure bracket is securely fastened before moving on to the next step.

(a) For Flat Back
No!

04
Top of TV

M-A M-C M-B
Use the shorter screws
M-E Not for M8 screws

Hardware Included
Arm and Wall Plate

Front Support

Arm Extensions

Brackets

01 x1

02 x1

Wrench

Extension A

Extension B

03 x2 Side Cover

04 x2 Front Cover

05 x1

6A x2

6B x2

Hardware cWall /Product)

Lag Bolts 5/16 x 2½ in

Open-end wrench

07 x2

08 x1
Hardware cProduct)
Nuts M8

x4

x1

A

B

TV Screws / Washers

Philips Screws M4 x 12mm M4 x 30mm

Philips Screws M6 x 15mm M6 x 30mm

Philips Screws M8 x 25mm M8 x 45mm

Spacers L10mm

C

Washers Ø6mm M4-5-6

Spacers L5mm

x4 x4

x4 x4 x4 x4

x8

x4

M-A

M-B

M-C

M-D

M-E

Step 2A Wall plate installation (wood stud)

x8
M-F
2

A-1

Max 610mm (24″)

Locate your studs. Verify and mark the center of the studs by finding the stud edges using an awl, a thin nail, and an edge-to-edge stud finder.

A-2
6B

Attach the Extensions to the Wall Plate

C

C

6A

Step 1-2 Select TV screw length
When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.

(b) For Round Back / Extra Space

No!

Too Short

Too Long

Correct

Correct

04
Top of TV

3

6A
M-A M-C M-B
Use the longer screws
M-E Not for M8 screws
M-D M-F

18″

6B

05

24″

For studs with the 18″ sapce
Only one side need to attach each of extension L and R

For studs with the 24″ sapce

4

5

7/32 in Ø5.5 mm
3/8in Ø 10 mm

2 2
V2

A-3

Bubble Level Mounting template

Position the mounting template at your desired height and line up the holes with your stud center line. Level the mounting template and mark the pilot hole locations.

Step 2B Wall plate installation (concrete or brick)

B-1
Position the mounting template at your desired height , level the mounting template and mark the pilot hole locations x4.

Bubble Level

A-4

V2
Mounting template

B-3
No!

Concrete wall anchor 4pcs (NOT INCLUDED)

Ø10*61mm

Contact us to have these additional pieces shipped directly to you.

A

2.75in (70 mm)

Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth
of 2 3/4 in (70 mm). Be sure to drill into the center of the stud.

A-5

Install wall plate 01 using lag bolts A

01

with Socket Wrench, NO Electrodrill.

Tighten the lag bolts A until they

are pulled firmly against the wall plate 01

To prevent the TV falling down, the Arrow Must Keep UP at this step!!
No!

05 A 6

Step 3 Install front support and extensions

3-1 Install the extensions 03 to front support 02 with the pre-assembled screws.

Back view

B-2

Ø 10 mm

Drill pilot holes

2.75in 70 mm

Step 4 Hang TV with brackets onto the arm extensions
04

01 To prevent the TV falling down, the Arrow Must Keep UP at this step!!
05
Use the included wrench 05 when have not the socket wrench in hand.
Install wall plate 01 using lag bolts A and anchor (not included) with Socket Wrench, NO Electrodrill. Tighten the lag bolts A until they are pulled firmly against the wall plate 01

7

8

Adjustments

TV leveling adjustment (-3°/+3°)
±3°
± 3°

1. Loosen a little

3. Insert the arm extension

2. Remove the pre-assembled screws x4

Assemble the side covers and the arm extensions with the preassembled screws

1. Hang
07

Fasten the all 8 screws.

Attach the front cover 2. Push to the front support

3-2

Hang 0022 onto 0011 and using a screwdriver to secure with pre-assembled screws P1 and washer P2 .

01
Adjustments Tilting Adjustment
-13° +5°

04 [SS33] Secure TV with brackets against the wall plate 01 with the pre-assembled screws [SS3] If necessary
If TV keeps tilting down, pull TV to desired angle then fasten tilting nuts with open-end wrench.

Loosen
Loosen 2 leveling bolts on the rear of TV plate with the open- end wrench B , adjust to level, and retighten to secure.
Product dimensions:
_ ¢

Tighten
B

¢

Tighten

Loosen

P1 P2

P1 P2
9

10

11