R2DSPOT150 150W LED Moving Head Spot Light
Product Information
Product Name: R2DSPOT150
Product Description: 150w led moving head
spot
User Manual: Available
Safety Instructions
This device has left the factory in perfect condition. In order
to maintain this condition and to ensure a safe operation, it is
absolutely necessary for the user to follow the safety instructions
and warning notes written in this user manual.
Unpacking
No information provided in the user manual.
Features & Specifications
- Light Source: 150W High Output White LED
- Working Modes: DMX, auto, sound,
master/slave - DMX Channels: 16/14/12/10 ch.
- Power Consumption: 200W
- Input Voltage: AC90-260V 50/60Hz
- Fuse: F5A / 250V
- Dimensions: 270(D)*270(W)*470(H)mm
- Packing Size: 305(D)*305(W)*500(H)mm
- Net Weight: 10.6kg
- Gross Weight: 12.6kg
Photometric Data
No information provided in the user manual.
Operation Instructions
The moving head is for spot effect for on-site decoration
purpose. Don’t turn on the fixture if it’s been through severe
temperature difference like after transportation because it might
damage the light due to the environment changes. So make sure to
operate the fixture until it is in normal temperature.
This light should be kept away from strong shaking during any
transportation or movement. Don’t pull up the light by only the
head, or it might cause damages to the mechanical parts. Don’t
expose the fixture to overheating, moisture, or environments with
too much dust when installing it. Also, don’t lay any power cables
on the floor as it might cause electric shock to people.
Before installing the fixture, ensure that the installation
place is in good safety condition. Use the safety chain and check
whether the screws are properly screwed when installing the
fixture. Make sure the lens is in good condition and replace the
units if there are any damages or severe scratches. The fixture
should be operated by qualified personnel who know the fixture
before using it. Keep the original packages if any second shipments
are needed. Do not try to change the fixtures without any
instruction by the manufacturer or the appointed repairing
agencies. Any malfunctions resulting from not following the user
manual or any illegal operation will not be covered under warranty
(e.g., shock, short circuit, electronic shock, lamp breakage,
etc.).
Installations
Cautions: For added protection, mount the fixtures in areas
outside walking paths, seating areas, or in areas where the fixture
might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the
installation area can hold a minimum point load of 10 times the
device’s weight. Fixture installation must always be secured with a
secondary safety attachment, such as an appropriate safety cable.
Never stand directly below the device when mounting, removing, or
servicing the fixture.
The fixture can be mounted from a ceiling or set on a flat level
surface. Ensure that the fixture is kept at least 0.5m (1.5ft) away
from any flammable materials (decoration, etc.). Always use and
install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails.
Mounting points for overhead mounting require extensive experience,
including amongst.
R2DSPOT150
150w led moving head spot
User Manual
1
1 SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes, do not switch it on immediately. The arising condensation could damage the device. Leave the device switched off until it has reached room temperature. This device falls under protection-class I. Therefore it is essential that the device be earthed. The electric connection must carry out by qualified person. The device shall only be used with rate voltage and frequency. Make sure that the available voltage is not higher than stated at the end of this manual. Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement of the cable must be done by an authorized dealer. Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord. During initial start-up some smoke or smell or smell may arise. This is a normal process and does not necessary mean that the device is defective, it should decrease gradually. Please don’t project the beam onto combustible substances. Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat radiation. If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer of his service agent or a similar qualified person in order to
2
avoid a hazard.
2 UNPACKING
Thank you for choosing our LED 150W moving head light. For your own safety, please read this manual before installing the device. This manual covers the important information on installation and applications. Please install and operate the fixture with following instructions. Meanwhile, please keep this manual well for future needs. The LED 150W is made of a new type of high temperature strength of engineering plastic and cast aluminum casing with nice outlook. The fixture is designed and manufactured strictly following CE standards, complying with international standard DMX512 protocol. It’s available independently controlled and linkable with each other for operation. And it is applicable for large-scale live performances, theater, studio, nightclubs and discos. The 150W Moving head light which features high brightness and stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during the transportation. And please check whether the following items are included inside the box:
3
3 FEATURES & SPECIFICATIONS
Features
150W High Output White LED 50,000 hours lifespan and low power consumption Beam Angle 15°, focus function Color Wheel: 7 colors +white, rotation with variable direction and speed 1 static Gobo Wheel: 8 gobos +white, wheel rotation and shake 1 Rotation Gobo Wheel: 6 gobos +white, wheel rotation and shake Prism: 3-facet Prism, bi-directionally rotatable at variable speeds Focus: electronic High speed strobe effect with 1-25 flashers per second 16/14/12/10 DMX Channels USITT DMX-512 DMX 512, master-slave and sound activated controllable or auto operation Colorful LCD display Efficient low noise fan cooling system POWERCON IN/OUT 3-pin XLR connectors IN/OUT Two 1/4 turn fastening Omega Clamps IP 20 protection rating
Specifications
Light Source: 150W High Output White LED Working modes: DMX, auto, sound, master/slave DMX Channels: 16/14/12/10 ch. Power Consumption: 200W Input Voltage: AC90-260V 50/60Hz Fuse: F5A / 250V Dimensions: 270(D)*270(W)*470(H)mm Packing size: 305(D)*305(W)*500(H)mm Net Weight: 10.6kg, Gross Weight:12.6kg
4
Dimensions
4 PHOTOMETRIC DATA
5 OPERATION INSTRUCTIONS
The moving head is for spot effect for on-site decoration purpose. Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature.
5
This light should be keep away from strong shaking during any transportation or movement.
Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.
Don’t expose the fixture in overheat, moisture or environment with too much dust when installing it. And don’t lay any power cables on the floor. Or it might cause electronics shock to the people.
Make sure the installation place is in good safety condition before installing the fixture. Make sure to put the safety chain and check whether the screws are screwed properly
when installing the fixture. Make sure the lens are in good condition. It’s recommended to replace the units if there
are any damages or severe scratch. Make sure the fixture is operated by qualified personnel who know the fixture before
using. Keep the original packages if any second shipments is needed. Don’t try to change the fixtures without any instruction by the manufacturer or the
appointed repairing agencies. It is not in warranty range if there are any malfunctions from not following the user
manual to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
6 INSTALLATIONS
Cautions: For added protection mount the fixtures in areas outside walking paths, seating
areas, or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 items the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
6
From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at least 0.5m (1.5ft) away from any flammable materials (decoration etc.). Always use and install the supplied safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp fails.
Mounting points: Overhead mounting requires extensive experience, including amongst
others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.
Clamp Mounting: The LED moving head provides a unique mounting bracket assembly that
integrates the bottom of the base, and the safety cable rigging point in one unit (see the illustration below). When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the “omega bracket”. As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable rigging point integrated in the base assembly.
7
Regardless of the rigging option you choose for your LED moving head, always be sure to secure your fixture with a safety cable. The fixture providers a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle.
7 DMX-512 CONTROL CONNECTIONS
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the moving head. You can chain multiple moving head together through serial linking. The cable needed should be two core, screened cable with XLR input and output connectors. Please refer to the diagram below.
8
For installations where the DMX cable has to run a long distance or is in an electrically noisy
enviroment, such as in a discotheque, it is recommended to use a DMX terminator. This helps
in preventing corruption of the digital control signal by electrical noise. The DMX terminator is
simply an XLR plug with a 120 resistor connected between pins 2 and 3, which is then
plugged into the output XLR socket of the last fixture in the chain. Please see illustrations
below.
.
8 MENU OPERATIONS
9
MENU
Address Set
[Set Address Numbers]Run Mode
[DMX] [AUTO] [SOUND] [MANUAL]Auto 1- Auto2 Manual Test
Function and Operation
Setup
[ Advanced Setting]Pan reverse Tilt reverse Display Screen Reverse Channel (16/14/12/10CH Select) Sensitivity (01-100) Motor zero Reset Factory Set
System Information
Ver V1 DMX Address Temperature
9 DMX CHANNELS
16/14/12/10/ channel mode sheet
CH10 CH12 14CH 16CH Function
Channel Value
Discription
CH1 CH1 CH1 CH1 Pan
0-255 0-540°
CH2 CH2 Pan fine
0-255 Pan Fine
10
CH2 CH2 CH3 CH3 Tilt CH4 CH4 Tilt Fine
0-255 0-270° 0-255 Tilt Fine
CH3 CH3 CH5 CH5 X, Y speed 0-255 From fast to slow
CH4 CH4 CH6 CH6 LED Dimmer 0-255 0 100%
0-7
Strobe open
CH5 CH5 CH7 CH7 LED Strobe 8-250 Strobe from slow to fast
251-255 Strobe open
0-15 White Lighting
16-31 Color 1
32-47 Color 2
7 color CH6 CH6 CH8 CH8
White
48-63 + 64-79
80-95
Color 3 Color 4 Color 5
96-111 Color 6
112-127 Color 7
128-191 CW from slow to fast
192-255 CCW from slow to fast
0-6
Open
7-13 Gobo 1
CH7 CH7
CH9
14-20
CH9
8 Static Gobos 21-27 +White
28-34
Gobo 2 Gobo 3 Gobo 4
35-41 Gobo 5
42-48 Gobo 6
11
CH8 CH9
49-55 Gobo 7 56-63 Gobo 8 64-70 Gobo 8 shake speed from slow to fast 71-77 Gobo 7 shake speed from slow to fast 78-84 Gobo 6 shake speed from slow to fast 85-91 Gobo 5 shake speed from slow to fast 92-98 Gobo 4 shake speed from slow to fast 99-105 Gobo 3 shake speed from slow to fast 106-112 Gobo 2 shake speed from slow to fast 113-119 Gobo 1 shake speed from slow to fast 120-127 Open
128-191 Gobo Rotating CW slow to fast
192-255 Gobo Rotating CCW slow to fast
CH10 6 rotation 0-15 gobos +White 16-31
open Gobo1
32-47 Gobo2
48-63 Gobo3
64-79 Gobo4
80-95 Gobo5
96-127 Gobo6
128-191 Gobo Rotate CW slow to fast
192-255 Gobo Rotate CCW slow to fast
0-15 CH11 Gobo Rotation
16-95
open Gobo Fine 0-360
12
96-135 Gobo Rotating 0-90
136-155 Gobo Rotating 0-180
CH8 CH10 CH10 CH12 Focus
156-175 Gobo Rotating 0-720 176-215 Gobo self-rotating CW from slow to
fast Gobo self-rotating CCW rotating from 216-255 slow to fast 0-255 0 100%
CH9 CH11 CH11 CH13 Prism
0-63 Open 64-255 Prism In
0-15 Stop
CH10 CH12 CH12 CH14 Prism Rotation 16-135 Rotate CW slow > fast
136-255 Rotate CCW slow > fast
self-setting CH13 CH15
Program
0-7
No action
8-131 Auto mode
132-255 Sound mode
0-249 No function
CH14 CH16 Reset
250-253 Reset
254-255 No function
10 MAINTENANCE AND CLEANING
The following points have to be considered during the inspection: 1) All screws for installing the devices or parts of the device have to be tightly connected and
must not be corroded. 2) There must not be any deformations on the housing, color lenses, fixations and installation
13
spots (ceiling, suspension, trussing). 3) Mechanically moved parts must not show any traces of wearing and must not rotate with
unbalances. 4) The electric power supply cables must not show any damage, material fatigue or sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed.
In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to the lights. 1) Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust. 2) Clean the fan each week. 3) A detailed electric check by approved electrical engineer each three month, make sure that the circuit contacts are in good condition, prevent the poor contact of circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol solvents. There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”. Should you need any spare parts, please order genuine parts from your local dealer.
14
