Trudoor Tde-e08 Escutcheon Lever Trim Instruction Manual (+ PDF)

Contents hide

TDE-E08 Escutcheon Lever Trim

Product Information:

The product is a cylinder collar used in conjunction with a
spring spindle. It is designed to extend the length of the spindle
if needed. The product also includes a cam and cam screws for
converting the TDE-E08 Entry function to Night latch function. The
product is compatible with the TDE-E08 and TDE-E14 models. It is
important to follow the provided instructions for proper
installation and usage.

Product Usage Instructions:

To extend the length of the spring spindle, follow these
steps:

Insert the spring into the spindle hole.

To convert the TDE-E08 Entry function to Night latch function,
follow these steps:

Locate the cam and cam screws on the back of the mortise
cylinder.
Remove the two cam screws and the cam.
Rotate the cam 180 degrees and re-install it in the down
position.
Re-install and tighten the cam screws, being careful not to
over tighten them.
Follow the TDE-E08 directions for installing the cylinder into
the trim.

Important Notes:

If using an outside trim, drill holes for the outside trim
first and install it before drilling holes for the exit
device.
If using a mullion, install the mullion first, then the outside
trim, and finally the exit device.
For TDE-E08 and TDE-E14 models, remove the orange sticker and
tighten the handing screw into hole A. Insert the spring first,
then the spindle into the back of the lever into hole E.
For 1000 series, screw thru bolts into the G holes. For 2000
series, screw thru bolts into the C holes and tighten them.
If a cylinder is required, install it into the cylinder hole
with the cylinder collar and secure it with the cylinder retaining
ring.
Follow the provided template for door templating according to
the series being used.

Note: The G holes are for 1000 series use, and the C holes are
for 2000 series use.

View Fullscreen

CYLINDER COLLAR

SPRING SPINDLE
Insert spring in spindle hole to extend the length of the spindle if required.

40″ above floor

Instructions for converting TDE-E08 Entry to Night latch function
TDE-E08 Entry function can be converted to Night latch function by inverting the cam on the mortise cylinder. The steps below show how to invert the cam:
Cam

Cam Screws

Step # 1:

Step # 2:

Locate cam and cam screws on the Remove the two cam screws and

back of the mortise cylinder.

the cam.

Do not insert the key while converting function.

Step # 3: Rotate cam 180 degrees and re-install in the down position. Re-install and tighten the cam screws being careful not to over tighten them as overtightened screws will make mortise cylinder difficult to operate. Step # 4: Follow TDE-E08 directions for installing cylinder into trim.

NOTE: 1.IF OUTSIDE TRIM IS BEING USED,
MAKE SURE TO DRILL HOLES FOR OUTSIDE TRIM FIRST AND INSTALL TRIM, THEN DRILL HOLES FOR EXIT DEVICE AND INSTALL. 2.IF MULLION IS BEING USED, INSTALL MULLION FIRST,THEN OUTSIDE TRIM, AND THEN EXIT DEVICE.
TDE-E08 / TDE-E14

IMPORTANT: REMOVE ORANGE STICKER AND TIGHTEN HANDING SCREW INTO HOLE “A” (SEE FIGURE 2 or 8) INSERT THE SPRING FIRST THEN THE SPINDLE INTO BACK OF LEVER INTO HOLE “E” (SEE FIGURE 2) 4. FOR 1000 SERIES SCREW THRU BOLTS INTO (4) G HOLES & FOR 2000 SERIES, SCREW THRU BOLTS INTO (4) C HOLES AND TIGHTEN. 5. IF CYLINDER IS REQUIRED, INSTALL CYLINDER INTO CYLINDER HOLE WITH CYLINDER COLLAR AND SECURE WITH CYLINDER RETAINING RING.
7. PROCEED WITH TEMPLATING DOOR AS SHOWN IN FIG 7 AND FIG 9 FOR EITHER 1000 OR 2000 SERIES.

NOTE:(A) 4 G HOLES ARE FOR 1000 SERIES USE. (B) 4 C HOLES ARE FOR 2000 SERIES USE.

7/16″ 7/16″ 7/16″ 7/16″

C 2 5/32″

2 15/16″

EXTERIOR

DOOR

2 7/16″

INTERIOR

A stock door backset of 2 3/4″ can be used but will decrease the backset by 3/16″, this can be offset by not using the 1/8″ strike shim to gain 1/8″ extra clearance. This will bring the backset within 1/16″ which is within acceptable tolerances to operate correctly.

FRAME

Rim Device on Single Door

3 5/16″ 3 5/16″

DOOR

2″ 2 7/16″ 2 7/16″

MULLION

If KRM Mullion is being used,install KRM mullion first, then outside trim adjusting backset according to KRM Mullion backset drawing and then install exit device.

Rim x Rim x Mullion on Pair of Doors

DOOR

2 5/8″

DOOR

When installing Rim device x SVR device on a pair of doors a Double Door Strike (DDS) is required. For complete template information, please refer to the DDS template.

DOUBLE DOOR STRIKE
3 9/32″

Rim w/ DDS x Surface Vertical Rod on a Pair of Doors

DOOR

2 3/4″ 2 3/4″
Surface Vertical Rod x Surface Vertical Rod on a Pair of Doors

For complete template information Please refer to Surface Vertical Rod exit device template.

7/16″

G 2 7/32″

7/16″

2 15/16″ 1 19/32″
9/16″

C 2 5/32″

Hole E-Drill 3/4″ hole for spindle

40″above floor