M20 12V ATV Broadcast Spreader
Product Information: MODEL # M20 12 Volt ATV Broadcast
Spreader
The MODEL # M20 is a 12 Volt ATV Broadcast Spreader manufactured
by EarthWay, a company that produces commercial, lawn & garden
tools. The spreader has a weight of 20lbs and can be mounted on the
front or rear rack of an ATV or quad. It comes with an adjustable
solid stop for rate setting control and a Control assembly that can
be installed to either the right or left Frame tube to allow for
use with the non-throttle hand. The spreader is designed to
distribute chemicals and other materials being applied for lawn and
garden purposes.
Product Usage Instructions
- Always wear protective clothing, eye wear, and dust mask to
prevent contact with chemicals and other materials being applied
with this machine. - Remove any material in the hopper before lifting or detaching
this machine from the vehicle. - Carefully lift the machine so as not to cause personal injury
or equipment damage. Do not attempt to install this machine to the
vehicle alone. Recruit the help of someone to assist when attaching
and detaching this machine from the vehicle. - Refer to the material packaging or the Material Safety Data
Sheet for precautionary measures required when handling materials
to be applied. - Before attaching this machine, consider the load capacity of
the vehicle. Refer to the owner’s manual of the vehicle for rated
load capacity. Take into account the weight of this machine is
20lbs and the weight of the material to be placed in the hopper
when calculating the total load. - Unpack all parts from shipping carton and ensure no parts are
missing. Refer to the exploded view for assembly instructions. - Attach the motor mount to the side of the hopper with the bolt
1/4-20 X 3/4 HHCS ZINC (#25), washer 5/8 OD X .257 ID ZINC (#22)
and wing nut 1/4-20 ZINC (#17). - Install the four (#9) 7/8 Tube plugs onto the ends of the two
(#15) Frames with the help of a hammer or some other tool. - Determine whether to mount on the front or the back of the
luggage rack. Depending on whether the M20 is mounted to the front
or rear rack, you will need to install (#4) Control assembly to
either the right (#11) or left (#15) Frame tube to allow for use
with the non-throttle hand. Wait until the unit is mounted to the
Quad before installing the Control. - Next install four 1/4-20 x 1-1/2 Carriage bolts (#12) through
the Hopper assembly and then through ONE of either side Frame and
secure with 1/4-20 Hex Nut (#8). - Position the M20 to the Quad and install the remaining Frame
member as outlined in step 4. Install the Control assembly (#4) to
the Frame and secure with a 1/4-20 x 1-3/4 Carriage bolt (#13) and
1/420 Hex Nut (#8) and tighten firmly to allow movement, but not
allow the lever to move unassisted. - Establish the correct rate and then lock the stop in that
position using the thumb wing nut on the setting control. - Read, understand, and follow all product label information
provided on the material being applied.
WARNING: Keep hands away from any spinning object, shut-off
plate, shut-off mechanism linkage, and the inside of the hopper,
extreme injury can occur.
MODEL # M20
12 Volt ATV Broadcast Spreader
ASSEMBLY INSTRUCTIONS
Thank you for selecting EarthWay for your spreader needs. Our production team in Northern Indiana takes pride in building this spreader. Our customer support team is standing ready to ensure your success. Please contact us at www.EarthWay.com to see our full line of commercial, lawn & garden tools.
IMPORTANT Always wear protective clothing, eye wear, and dust mask to prevent contact with chemicals and other
materials being applied with this machine.
Remove any material in the hopper before lifting or detaching this machine from the vehicle.
Care must be taken when lifting this machine so as not to cause personal injury or equipment damage. Never attempt to install this machine to the vehicle alone. Recruit the help of someone to assist when attaching and detaching this machine from the vehicle.
Refer to the material packaging or the Material Safety Data Sheet for precautionary measures required when handling materials to be applied.
Before attaching this machine, consideration must be given to the load capacity of the vehicle. Refer to the owner’s manual of the vehicle for rated load capacity. Be sure to take into account the weight of this machine is 20lbs. and the weight of the material to be placed in the hopper when calculating the total load.
M20_REV_JUNE_2022
PAGE 1
Assembly and Operation Instructions
Assembly Instructions
STEP 1: Unpack all parts from shipping carton to ensure no parts are missing. Refer to the exploded view.
STEP 2: Attach the motor mount to the side of the hopper with the bolt 1/4-20 X 3/4″ HHCS ZINC (#25), washer 5/8″ OD X .257 ID ZINC (#22) and wing nut 1/4-20 ZINC (#17).
STEP 3: Install the four (#9) 7/8″ Tube plugs onto the ends of the two (#15) Frames with the help of a hammer or some other tool.
STEP 4: Determine whether to mount on the front or the back of the luggage rack. Depending on whether the M20 is mounted to the front or rear rack, you will need to install (#4) Control assembly to either the right (#11) or left (#15) Frame tube to allow for use with the non-throttle hand. Wait until the unit is mounted to the Quad before installing the Control.
STEP 5: Next install four 1/4-20 x 1-1/2″ Carriage bolts (#12) through the Hopper assembly and then through ONE of either side Frame and secure with 1/4-20 Hex Nut (#8).
STEP 6: Now position the M20 to the Quad and install the remaining Frame member as outline above in STEP 4. Now install the Control assembly (#4) to the Frame and secure with a 1/4-20 x 1-3/4″ Carriage bolt (#13) and 1/420 Hex Nut (#8) and tighten firmly to allow movement, but not allow the lever to move unassisted.
Now install the M20 on your quad as outlined on the following page.
WARNING
KEEP HANDS AWAY FROM ANY SPINNING OBJECT, SHUT-OFF PLATE, SHUT-OFF MECHANISM LINKAGE, AND THE INSIDE OF THE HOPPER, EXTREME INJURY CAN OCCUR.
Earthway_M20 Manual
PAGE 2
Assembly and Operation Instructions
HOW TO OPERATE SAFELY
Read, understand, and follow all product label information provided on the material being applied. An adjustable solid stop is provided that allows the operator to adjust to the desired opening position on the rate setting control prior to operation of the vehicle. This allows repeatability to the stop without the need to look at the control while operating the vehicle. Establish the correct rate and then lock the stop in that position using the thumb wing nut on the setting control.
OPERATING INSTRUCTIONS
Before filling hopper, become familiar with the operation of this spreader. (Practice the following steps.
Turn the motor switch to the ON POSITION, so that the impeller is turning before going on to the next step.
While driving forward pull the lever back to the stop, this opens the shut off plate on the spreader. To stop the flow of material, Push the lever to “0” or closed position, then turn the motor off when finished. When finished empty any remaining material from hopper. Thoroughly wash spreader and allow to dry before storing. A light coating of oil will help prevent corrosion of all
metal surfaces.
MOUNTING INSTRUCTIONS
Position the M20 on the vehicle so that the impeller is positioned to be able to spin clear of any part of the vehicle, this will allow a full 180 degree spread pattern. Secure the frame to the mounting location with the enclosed J-Bolts at positions that will secure the spreader so that it will not move when operating the vehicle. For best results mount the spreader so that the impeller is as close to the vehicle as possible but clears any parts on the vehicle and place the JBolts as shown below. Connect the black wire (ground) to the negative (-) post on the battery and the fused wire to the positive (+) post on the battery.
If for any reason the impeller rotates counterclockwise, reverse the battery connection of the spreader. Correct rotation is clockwise.
Earthway_M20 Manual
PAGE 3
Assembly and Operation Instructions
SPREADER CALIBRATION INSTRUCTIONS
Loosen stop on the gauge and set to #30 Open the lever to #30 and make sure that the shut-off is fully open. Loosen the cable clamp on the bottom of the hopper and slide the outer cable IN/Out until the shut-off is fully
OPEN. Tighten the cable clamp and retest. Calibration is now complete
TO CALCULATE THE SETTING
Determine how much material is to be applied per 1,000 sq/ft. Measure off a distance of 50 feet, preferably on a paved surface such as a parking lot.
Weigh out enough of the material to be applied to fill the hopper at least half full. Record the weight for future use.
With the unit mounted on the vehicle and the hopper at least half full of the material to be spread, position the vehicle far enough before the beginning of the 50-foot test area so that the vehicle will achieve the desired speed before you reach the starting line.
Set the rate setting stop at a position that you feel would be an appropriate setting. Start the vehicle in motion and as you cross the starting line (of the 50 feet) move the rate lever to the open
position against the stop. Take care to be aware of what is going on around you maintaining control of the vehicle. Continue from the starting line with the unit spreading the material. As you cross the finish line move the rate lever to the closed position. Stop the vehicle and note the width of the spread path that was just completed. Return to the start point and empty the remaining material from the hopper into your weighing container and re-weigh.
All spare parts listed herein may be ordered direct from the manufacturer. Be sure to give the following information when ordering.
1. Model Number 2. Part Number 3. Part Description
You can contact us by calling (574) 848-7491 to place an order with a credit card, or purchase online at www.Earthway.com. Questions? Email us at [email protected]
Earthway_M20 Manual
PAGE 4
Assembly and Operation Instructions
Earthway_M20 Manual
PAGE 5
Assembly and Operation Instructions
Key # Part #
Description
M20 Parts List
Key #
Part #
Description
1
77003
HEAVY DUTY RAIN COVER
16
43050
U-BOLT STRAP (M20)
2
70179
MOTOR 12V POLOLU
17
32103
NUT 1/4-20 WING ZINC
3
60320
MOTOR SUPPORT ASSEMBLY (M20)
18
12318
LOWER HOUSING CLIP
4
60523
CONTROL ASSEMBLY-M20 REV907
19
12221
SHUT OFF PLATE
5
60322
HOPPER ASSEMBLY (M20)
20
31138
#8 X 3/8″ PMT #8 HD COARSE BLACK
6
44287
“J” BOLT (M30/M20)
21
12109
IMPELLER (9″ DIA)
7
60511
WIRE HARNESS ASSEMBLY (M20/M30)
22
34108
9/16″ OD. X .257 ID. WASHER ZINC
8
32100
1/4-20 HEX NUT ZINC
23
12364
MODIFIED MOTOR BASE
9
19132
7/8″ TUBE PLUG
24
12311
MOTOR CAP (M20)
10
31155
SCREW #6-32 X 3/4 SS
25
31101
1/4-20 X 3/4″ HHMS ZINC
11
25118
FRAME (M20) REV 907 RIGHT
26
32106
10-24 WING NUT ZINC
12
37101
1/4-20 X 1 1/2″ CARRIAGE BLT Z
27
12222
INDICATOR-BROADCAST
13
37108
1/4-20 X 1 3/4″ CARRIAGE BOLT ZINC
28
60422
MOTOR ASSEMBLY (M20)
14
31124
#10 X 5/8″ TYPE A PHPS ZINC
29
77032
STRAIN RELIEF (#1184) HEYCO
15
25119
FRAME (M20) REV 907 LEFT
30
25800
COUPLER-8MM w/SET SCREWS
Installation the 77122 3-Sided Deflector Kit requires drilling of the hopper and motor support assembly for fitting.
Earthway_M20 Manual
PAGE 6
Assembly and Operation Instructions
EC DECLARATION OF CONFORMITY (Machinery Directive & Electromagnetic Compatibility Directives)
Herewith we declare that the machinery described below is in accordance with the relevant health and safety requirements of the EC Council Directives concerned with Machinery and Electromagnetic Compatibility. No alterations are to be made to the machine without prior consultation and approval of Earthway Products, Inc. otherwise the Declaration may become invalid. This equipment must be commissioned, used, and maintained strictly in accordance with the operating and maintenance instructions issued with the machine. Operators must be trained in accordance with the recommendations given in the operating and maintenance instructions issued with the machine.
Description of Machine: EarthWay® M20 12-volt Broadcast Spreader Description of Machine: EarthWay® M20 12-volt Broadcast Spreader Date of Supply: AS INVOICED DATE Relevant EC Council Directives: Machine Directives 89/392/EEC and subsequent amendments. Electromagnetic compatibility Directive 89/336/EEC and subsequent amendments.
DO NOT RETURN TO DEALER FOR REPAIR
CUSTOMER SERVICE
[email protected] | 1009 Maple Street, Bristol, IN 46507
Earthway_M20 Manual
PAGE 7
Assembly and Operation Instructions
ONE YEAR WARRANTY
EarthWay Products, Inc. warrants this product free of defects in original workmanship and materials for a period of one year to the end user with the original purchase receipt. If a manufacturing non-conformance is found, EarthWay Products, Inc. at its discretion will repair or replace the part(s)/product at no charge provided the failure is not the result of incorrect installation, mishandling, misuse, tampering, or normal wear and tear as determined by EarthWay.
EarthWay at its discretion may require that the part(s) or product be returned along with the original purchase receipt for examination and compliance with the terms of this warranty. Do not return any product without first receiving authorization from EarthWay Products, Inc.
To seek remedy under this warranty, contact EarthWay Products, Inc. at [email protected] or write to EarthWay Products, Inc. 1009 Maple Street, Bristol, IN 46507 and describe the nature of the manufacturing defect. SPECIFIC LIMITATIONS: This warranty covers only the part(s) or product; any labor charges associated with repair or replacement of nonconformances are specifically excluded. Due to the corrosive nature of most fertilizers and ice melt products, EarthWay Products, Inc. makes no warranty against and specifically excludes part(s) or product degradation or failure due to corrosion or its effects.
Earthway_M20 Manual
PAGE 8
Spreaders, Fertilizer, and Garden Tools for Your Lawn - EarthWay
