Karlik Gk-1e Computer Sockets User Manual

GK-1e Computer Sockets

Product Information

The manual provides information on the following types of
sockets:

• DECO
• ICON
• MINI
• FLEXI
• TREND
• LOGO

The product symbol includes:

• DGK-1e, DGK-3, DGK-5, DGK-2, DGK-4, DGK-6, DGTK
• IGK-1e, IGK-3, IGK-5, IGK-2, IGK-4, IGK-6, IGTK
• MGK-1e, MGK-3, MGK-5, MGK-2, MGK-4, MGK-6, MGTK
• FGK-1e, FGK-3, FGK-5, FGK-2, FGK-4, FGK-6, FGTK
• GK-1e, GK-3, GK-5, GK-2, GK-4, GK-6, GTK
• LGK-2

Product Usage Instructions

Follow these instructions to assemble the screen socket
RJ45:

1. Take the plastic cap and the right and left claps of the module
   (as shown in photo no.1).
2. Take the open claps of the module and the wire screen of the
   wire (as shown in photo no.3).
3. Place the wire screen of the wire on the open claps of the
   module and cover it with the plastic cap (as shown in photo
   no.4).
4. Strip the screen of the wire and place it in between the right
   and left claps of the module (as shown in photo no.5).
5. Cover the stripped screen of the wire with the plastic cap (as
   shown in photo no.5).
6. Align the arrow on the cap with the arrows on the module (as
   shown in photo no.6).
7. Press the cap down until it clicks into place (as shown in
   photo no.7).
8. The assembly should be done by a suitably qualified person with
   deactivated voltage and should meet national safety standards (as
   mentioned in note in photo no.9).

ASSEMBLY MANUAL ­ COMPUTER SOCKETS

The manual concerns the following types of sockets:

Series DECO ICON MINI FLEXI TREND LOGO

Symbol of the product DGK-1e, DGK-3, DGK-5, DGK-2, DGK-4, DGK-6, DGTK IGK-1e, IGK-3, IGK-5, IGK-2, IGK-4, IGK-6, IGTK MGK-1e, MGK-3, MGK-5, MGK-2, MGK-4, MGK-6, MGTK FGK-1e, FGK-3, FGK-5, FGK-2, FGK-4, FGK-6, FGTK GK-1e, GK-3, GK-5, GK-2, GK-4, GK-6, GTK LGK-2

Assembly manual on the example of the screen socket RJ45 (when it comes to a non-screen socket proceed in the same manner):

1. Prise the clasps from both sides and open the module (Photo no. 1). 2. Remove the plastic cap with markings of the ways of assembly: A or B (Photo no. 2). 3. Strip insulation of the wire and leave 1 cm screen (Photo no. 3). 4. Lead the stripped wire through the plastic cap, leaving screen (Photo no. 4). 5. Pull the cords of the wire through notches of the plastic cap, keeping suitable colour of the chosen connection standard A or B (Photo no. 5). 6. Cut the projecting ends of the cords (Photo no. 6). 7. Insert the plastic cap into the module following the arrows directions both on the cap and on the module (Photo no. 7). 8. Close the module. This way the cap shall be pressed automatically (Photo no. 8). 9. Press the screen of the wire to the module casing with the cable tie and block it (Photo no. 9).

Photo no.1

plastic cap

right clap of the module

left clap of the module

Photo no. 2 .
Photo no. 4

plastic cap

Photo no. 3

open claps of the module
wire screen of the wire

Photo no. 5
stripped screen of the wire plastic cap

1 I 2

ASSEMBLY MANUAL ­ COMPUTER SOCKETS

Photo no. 6

Photo no. 7

arrow on the cap arrows on the module

Photo no. 8

Photo no. 9

NOTE! Assembly shall be held by a suitably qualified person with deactivated voltage and shall meet the national safety standards
2 I 2