Product Information
| Product Name | Modular Nav Light |
|---|---|
| Part Number | 69640H-X-X |
Product Usage Instructions
Parts/Tools Needed:
- Screws Bezel Mount (not provided)
- Power Drill (not provided)
- Marine Wire Connectors (not provided)
- Application Specific Sealant (not provided)
Backnut No Bezel Version:
Mounting angle must be on vertical surface and 56.25 degrees to
meet coast guard requirements*
- Drill a 7/8 hole in your mounting surface then feed the wires
through the pre-drilled hole. - Wire the light using the wiring diagram. Use application
specific sealant around the light to prevent any ingress of water.
Screw on the back nut to the light until tight.
Screw Mount Bezel Version:
Mounting angle must be on vertical surface and 56.25 degrees to
meet coast guard requirements*
- Drill a 7/8 hole in your mounting surface and predrill screw
holes. Feed the wires through the pre-drilled 7/8 hole. - Wire the light using the wiring diagram. Use application
specific sealant around the light to prevent any ingress of water.
Screw on the bezel.
Wiring Diagram:
Wire the light based on the wiring diagram. Use silicone sealant
around the light to prevent any ingress of water.
| Incoming | 12V – 24V DC | |
|---|---|---|
| Power | Load (+) | Neutral (-) |
| Fuse | Black (-) | Red (+) |
| Nav Light |
Contact Information:
3030 Corporate Grove Dr. Hudsonville, MI 49426
Phone: 616.396.1355
Website: itc-us.com
Modular Nav Light
Part#: 69640H-X-X
PARTS/TOOLS NEEDED:
INSTALLATION INSTRUCTIONS
Navigation Light
Screws Bezel Mount Only
(not provided)
Power Drill
(not provided)
Marine Wire Connectors
(not provided)
INSTALLATION CONSIDERATIONS · Disconnect power before installing, adding or changing any component.
· To avoid a hazard to children, account for all parts and destroy all packing materials.
· It is recommended that fuse protection be added to the positive (+) input.
· All electrical connections should be made inside a watertight junction box. · *Visit https://www.uscgboating.org/regulations/navigation-rules.php for full navigation regulations.
Application Specific Sealant
(not provided)
Backnut No Bezel Version | Mounting angle must be on vertical surface and 56.25 degrees to meet coast guard requirements*
1. Drill a 7/8″ hole in your mounting surface then feed the wires
through the pre-drilled hole.
2. Wire the light using the the wiring diagram. Use application
specific sealant around the light to prevent any ingress of
water. Screw on the back nut to the light until tight.
Screw Mount Bezel Version | Mounting angle must be on vertical surface and 56.25 degrees to meet coast guard requirements*
1. Drill a 7/8″ hole in your mounting surface and predril screw
holes. Feed the wires through the pre-drilled 7/8″ hole.
2. Wire the light using the the wiring diagram. Use application
specific sealant around the light to prevent any ingress of
water. Screw on the bezel.
Wiring DiagramWire the light based on the wiring diagram. Use silicone sealant around the light to prevent any ingress of water.
Incoming 12V – 24V DC
Power
Load (+) Neutral (-)
Fuse
Black (-)
Red (+)
Nav Light
3030 Corporate Grove Dr. Hudsonville, MI 49426 Phone: 616.396.1355 itc-us.com
For warranty information please visit www.itc-us.com/warranty-return-policy DOC #: 710-00153 · Rev C · 06/19/23
Page 1 of 1
ITC Warranty & Return Policy
Navigtion Rules
