X7 Sauna Room
Model X7 Sauna Room Installation Manual
The Model X7 Sauna Room comes with the following components:
- Floor Raiser 1 (2)
- Floor Raiser 2 (2)
- Support Rail 1 (4)
- Support Rail 2 (4)
- Back Wall 1 (1)
- Back Wall 2 (1)
- Back Wall 3 (1)
- Side Wall 1 (2)
- Side Wall 2 (1)
- Side Wall 3 (1)
- Window Element (2)
- Door Element (1)
- Roof 1 (1)
- Roof 2 (1)
- Roof 3 (1)
- Bench (1)
- Side Bench (1)
- Backrest (1)
- Lower Backrest (1)
- Bench Support (2)
- Side Bench Support 1 (1)
- Side Bench Support 2 (1)
- Cornice Board 1 (1)
- Cornice Board 2 (2)
- Heater Cover (1)
- Front Wall Cover Slat (2)
- Vent Cover (1)
- Door Handle (1)
- Footrest (1)
- Screws 4.5 x 80mm (.19 x 3.14) (QTY 8)
- Screws 4.5 x 70mm (.17 x 2.75) (QTY 44)
- Screws 4 x 60mm (.15 x 2.36) (QTY 8)
- Screws 4 x 50mm (.15 x 1.96) (QTY 48)
- Screws 3.5 x 40mm (.13 x 1.57) (QTY 26)
Product Usage Instructions
Step 1: Connect the Four Floor Risers
- Fasten the four Floor Risers together using Screws 4.5×80,
being sure the two shorter boards are located on the sides and the
two longer boards are on the front and back. - Use a framing square to ensure the assembly is square.
Step 2: Connect Wall Support Rails
- Insert the Tenons of Support Rail 1 in the longer support rail
holes. - Fasten the wall support rails together and connect from corners
using four Screws 3.5×20 per corner.
Step 3: Position Wall Support Rails
- Lay the wall support rail assembly squarely on top of the floor
risers with the groove facing up. - The rails should overlap both sides of the riser by
approximately 0.5 inches. - Secure the assembly to the floor risers using four Screws 4×50
evenly spaced on each wall support rail.
Step 4: Position Wall Sections (Back Wall 1 & Side
Wall1)
- Position Back Wall Section 1 in the groove of the back rail and
push it flush against the left rail. - Have a helper hold back wall section.
- Orient Side Wall Section 1 and place it in the groove of the
left rail. - Push the flat edge flush against back wall section.
- Align the two panels so they are flush and fasten them using
Screws 4.5×70.
Step 5: Position Back Wall Sections 2 & 3, and Side
Wall 1
- Position Back Wall 2 section into the groove of the back
rail. - Attach it to Back Wall section 1 by way of the tongue and
groove fit. - Secure it by tapping it into place with a rubber mallet.
- Repeat this step for Wall Section 3, again tapping it into
place with a rubber mallet. - Position Side Wall Section 1 into the groove to the right side
rail and push flush against the back wall. - Be sure panels are flush with each other.
- Fasten them using Screws 4.5×70.
Step 6: Position Side Wall Section 2, Window Section
& Door Section
- Position Side Wall Section 2 in the groove of the right rail
and push flush against the back wall. - Position Window Element in the groove to the right of Side Wall
Section 2. - Position Door Element in the groove to the left of Side Wall
Section 2.
Step 7: Position Side Wall Section 3 and Window
Section
- Position Side Wall Section 3 in the groove of the right rail
and push flush against the back wall. - Position Window Element in the groove to the right of Side Wall
Section 3.
Step 8: Assemble and Position Roof Support
Rails
- Reference Step 2 and connect Roof Support Rails in the same
way. - Place the assembly on top of the wall sections so that the wall
sections fit snugly into the groove. - When in place, secure to the assembly to the walls using four
Screws 4×50 on each rail.
Model X7 Sauna Room Installation Manual
Floor Raiser 1
2
Floor Raiser 2
2
Support Rail 1
4
Support Rail 2
4
Back Wall 1
1
Back Wall 2
1
Back Wall 3
1
Side Wall 1
2
Side Wall 2
1
Side Wall 3
1
Window Element
2
Door Element
1
Roof 1
1
Roof 2
1
Roof 3
1
Bench
1
Side Bench
1
Backrest
1
Lower Backrest
1
Bench Support
2
Side Bench Support 1
1
Side Bench Support 2
1
Cornice Board 1
1
Cornice Board 2
2
Heater Cover
1
Front Wall Cover Slat
2
Vent Cover
1
Door Handle
1
Footrest
1
Screws 4.5 x 80mm (.19″ x 3.14″) 4.5 x 70mm (.17″ x 2.75″) 4 x 60mm (.15″ x 2.36″) 4 x 50mm (.15″ x 1.96″) 3.5 x 40mm (.13″ x 1.57″)
[PP[ Vent Cover Washer Tenon
QTY 8 44 8 48 26 16 1 8
Step 1. Connect the Four Floor Risers
Fasten the four Floor Risers together using 4.5×80 screws, being sure the two shorter boards are located on the sides and the two longer boards are on the front and back. Use a framing square to ensure the assembly is square.
Pre-drill holes for the screws
Floor Raiser 1
Floor Raiser 2
Screws 4.5×80
Step 2. Connect Wall Support Rails
Each wall support has a pre-drilled hole for a Tenon. Insert the tenons in the longer support rail holes. Fasten the wall support rails together and connect from corners using four 3.5×20 screws per corner.
Floor Raiser 2 Floor Raiser 1
Support Rail 1
Tenon
Support Rail 2
Support Rail 1
Support Rail 2
Support Rail 1 Screws 3.5×20
Step 3. Position Wall Support Rails
Lay the wall support rail assembly squarely on top of the floor risers with the groove facing up. The rails should overlap both sides of the riser by approximately 0.5″.
Secure the assembly to the floor risers using four 4×50 screws evenly spaced on each wall support rail
Screws 4×50
Step 4. Position Wall Sections (Back Wall 1 & Side Wall1)
Position Back Wall Section 1 in the groove of the back rail and push it flush against the left rail. Have a helper hold back wall section. Orient Side Wall Section 1 and place it in the groove of the left rail. Push the flat edge flush against back wall section. Align the two panels so they are flush and fasten them using 4.5×70 screws
Pre-drill holes for the screws
Vent Holes On Top!
Back Wall 1
Screws 4.5×70
Side Wall 1
Step 5. Position Back Wall Sections 2 & 3, and Side Wall 1
Position Back Wall 2 section into the groove of the back rail. Attach it to Back Wall section 1 by way of the tongue and groove fit. Secure it by tapping it into place with a rubber mallet. Repeat this step for Wall Section 3, again tapping it into place with a rubber mallet. Position Side Wall Section 1 into the groove to the right side rail and push flush against the back wall. Be sure panels are flush with each other. Fasten them using 4.5×70 screws.
Pre-drill holes for the screws
Side Wall 1
Back Wall 3 Back Wall 2 Screws 4.5×70
Step 6. Position Side Wall Section 2, Window Section & Door Section
Position Side Wall Section 2 into the groove of the side rail. Slide Side Wall Section 2 into place with side wall section1. Section 2 connects to Section 1 via tongue and groove so there is no need to use screws. Use a rubber mallet to secure the fit. Place Window Section in the groove on the front rail and push against side rail. Be sure the two sections are flush and fasten them using 4.5×70 screws. Place Door Section onto the front rail orienting it so that the door opens according to your preference. Door Section connects to Window Section via tongue and groove so there is no need for screws. Gently tap it into place with a rubber mallet to secure the fit.
Side Wall 2 Screws 4.5×70
Window Door Element
Step 7. Position Side Wall Section 3 and Window Section
Position Side Wall Section 3 into the groove of the side rail so that the heater vent holes are located at the bottom. Slide wall section into place with Side Wall Section 1. Side Wall 3 connects to Side Wall 1 via tongue and groove so there is no need to use screws. Use a rubber mallet to secure the fit. Next, place the Window Section into the groove of the front rail and connect it to the Door Section via the tongue and groove fit. Gently tap into place with a rubber mallet to secure the fit. Now, making sure Window Section and Side Wall 3 are flush with each other, secure them with 4.5×70 screws.
Pre-drill holes for the screws
Window
Step 8. Assemble and Position Roof Support Rails
Reference step 2 and connect Roof Support Rails in the same way. Place the assembly on top of the wall sections so that the wall sections fit snugly into the groove. When in place, secure to the assembly to the walls using four 4×50 screws on each rail.
Side Wall 3 Screws 4.5×70
Screws 4×50
Roof Support Rail
Step 9. Bench Installation
Use 4.5×70 screws to connect the Bench Supports to the wall. Make sure the supports in both walls are in same height. When the supports are assembled place the bench on the supports. Use three 4.5×70 screws to connect the seat bench to the back wall.
Bench Support
Screws 4.5×70
Screws 4.5×70
30.75″
Step 10. Side Bench Installation
Attach the Side Bench Support 1 to the back wall using two 4.5×70 screws. Side Bench Support 2 connects to the Window Section using 4×60 screws. Place the side bench on the supports and fasten wit three 4.5×70 screws to the side wall element.
16.1″
Side Bench Support 2
Screws 4×60
Screws 4.5×70
Pre-drill holes for the screws
Side Bench Support 1
Screws 4.5×70
Step 11. Backrest and Lower Backrest Installation
Center the Backrest between the two sides and position it vertically at a height most comfortable for you (typically 8-12″ from the bench). Using a level to ensure proper installation, fasten the Backrest into place using 4×60 screws. Using a level, secure the Lower Backrest to side wall section with 4×60 screws at the same height above the upper long bench.
Backrest
Pre-drill holes for the screws.
Screws 4×60
Lower Backrest Screws 4×60
Step 12. Position Roof Sections
Place the Roof Panels on top of the ceiling supports. Connect the sections via the tongue and groove fit. From the backside, roof panels must be in the same line with ceiling supports. Position the both sides
equally 1.875″. Connect panels with 4×50 sRcroewosf. 1
Roof 2
Roof 3
Screws 4×50
Pre-drill holes for the screws
Step 13. Cornice Boards
Connect the Cornice Boards to the roof, using 3.5×40 screws.
Cornice Board 2
Cornice Board 2
Cornice Board 1
Screws 3.5×40
Step 14. Cover Slats to the Front Wall
Connect the Cover Slats using 3.5×40 screws
Step 15. Heater Cover
Connect the Heater Cover to the wall with 4×60 screws. Perform this step after the heater is installed. Note: Follow heater manufacturer recommended installation for heater guard.
Screws 3.5×40
Cover Slat
Pre-drill holes for the screws
Step 16. Vent Cover & Door Handle
Connect the Vent Cover with 3.5×40 screw. Between wall and Vent Cover add small washer.
Screws 4×60
Step 17 Footrest Installation
Connect the Footrest with 4.5×70 screws from one side to the Side Bench and from the other side to the side wall. Two screws per side. Measure from front wall must be 22.14″
20″
Footrest
Screws 4.5×70 Floorplan View
REV: X703923
