X6 Traditional 4-6 Person Indoor Sauna
Product Information: Model X6 Sauna Room
The Model X6 Sauna Room is a complete sauna kit that includes
all the necessary components to build a sauna room. The kit
includes various wall and bench sections, support rails, floor
raisers, door element, window element, and other hardware
components. The sauna room is designed to provide a comfortable and
relaxing sauna experience.
Product Components
- Floor Raiser 1 (2)
- Floor Raiser 2 (2)
- Support Rail 1 (4)
- Support Rail 2 (4)
- Back Wall 1 (1)
- Back Wall 2 (1)
- Back Wall 3 (1)
- Side Wall 1 (2)
- Side Wall 2 (1)
- Side Wall 3 (1)
- Window Element (2)
- Door Element (1)
- Roof 1 (1)
- Roof 2 (2)
- Upper Bench (1)
- Lower Bench (1)
- Side Bench (1)
- Backrest 1 (1)
- Backrest 2 (1)
- Backrest 3 (1)
- Bench Support 1 (2)
- Bench Support 2 (2)
- Side Bench Support 1 (1)
- Side Bench Support 2 (1)
- Backrest 2 Vertical Slat (3)
- Cornice Board 1 (1)
- Cornice Board 2 (2)
- Heater Cover (1)
- Front Wall Cover Slat (2)
- Vent Cover (1)
- Door Handle (1)
- Screws (various sizes and quantities)
- Vent Cover Washer (1)
- Tenon (1)
Product Usage Instructions:
Step 1. Connect the Four Floor Risers
- Fasten the four Floor Risers together using 4.5×80 screws.
- Place the two shorter boards on the sides and the two longer
boards on the front and back. - Use a framing square to ensure that the assembly is
square.
Step 2. Connect Wall Support Rails
- Insert the tenons in the longer support rail holes.
- Fasten the Wall Support Rails together and connect from corners
using four 3×20 screws per corner.
Step 3. Position Wall Support Rails
- Lay the wall support rail assembly squarely on top of the floor
risers with the groove facing up. - The rails should overlap both sides of the riser by
approximately 0.5. - Secure the assembly to the floor risers using four 4×50 screws
evenly spaced on each wall support rail.
Step 4. Position Wall Sections (Back Wall 1 & Side
Wall 1)
- Position Back Wall 1 in the groove of the back rail and push it
flush against the left rail. - Orient Side Wall Section 1 and place it in the groove of the
left rail. - Push the flat edge flush against the back wall section.
- Align the two panels so they are flush and fasten them using
the 4.5×70 screws.
Step 5. Position Back Wall sections 2 & 3, &
Side Wall 1
- Position Back Wall 2 section into the groove of the back
rail. - Attach it to Back Wall Section 1 by way of the tongue and
groove fit. - Secure it by tapping it into place with a rubber mallet.
- Repeat this step for wall section 3, again tapping it into
place with a rubber mallet. - Position Side Wall Section 1 into the groove of the right side
rail and push flush against the back wall. - Be sure panels are flush with each other and fasten them
together using the 4.5×70 screws.
Step 6. Position Side Wall Section 2, Window Section
& Door Element
- Position Side Wall Section 2 into the groove of the side
rail. - Slide Side Wall Section 2 into place with Side Wall Section
1. - Section 2 connects to Section 1 via tongue and groove so there
is no need to use screws. - Use a rubber mallet to secure the fit.
Model X6 Sauna Room Installation Manual
Floor Raiser 1
2
Floor Raiser 2
2
Support Rail 1
4
Support Rail 2
4
Back Wall 1
1
Back Wall 2
1
Back Wall 3
1
Side Wall 1
2
Side Wall 2
1
Side Wall 3
1
Window Element
2
Door Element
1
Roof 1
1
Roof 2
2
Upper Bench
1
Lower Bench
1
Side Bench
1
Backrest 1
1
Backrest 2
1
Backrest 3
1
Bench Support 1
2
Bench Support 2
2
Side Bench Support 1
1
Side Bench Support 2
1
Backrest 2 Vertical Slat
3
Cornice Board 1
1
Cornice Board 2
2
Heater Cover
1
Front Wall Cover Slat
2
Vent Cover
1
Door Handle
1
Screws 4.5 x 80mm (.19″ x 3.14″) 4.5 x 70mm (.17″ x 2.75″) 4 x 60mm (.15″ x 2.36″) 4 x 50mm (.15″ x 1.96″) 3.5 x 40mm (.13″ x 1.57″) 3.5 x 35mm (.13″ x 1.37″) 3.5 x 25mm (.13″ x .98″)
3 x 20mm (.11″ x .78″) Vent Cover Washer Tenon
QTY 8 47 8 50 28 6 9 16 1 8
Step 1. Connect the Four Floor Risers
Fasten the four Floor Risers together using 4.5×80 screws. Be sure the two shorter boards are located on the sides and the two longer boards are on the front and back. Use a framing square to ensure that the assembly is square.
Floor Raiser 1
Pre-drill holes for the screws
Floor Raiser 2
Screws 4.5×80
Floor Raiser 2
Step 2. Connect Wall Support Rails
Each wall support has a pre-drilled hole for the Tenon. Insert the tenons in the longer support rail holes. Fasten the Wall Support Rails together and connect
from corners using four 3×20 screws per corner. Support Rail 1
Floor Raiser
Tenon
Tenon
Support Rail 2 Support Rail 1
Support Rail 2
Screws 3×20
Support Rail 1
Step 3. Position Wall Support Rails
Lay the wall support rail assembly squarely on top of the floor risers with the groove facing up. The rails should overlap both sides of the riser by approximately 0.5″. Secure the assembly to the floor risers using four 4×50 screws evenly spaced on each wall support rail
Screws 4×50
Step 4. Position Wall Sections (Back Wall 1 & Side Wall 1)
Position Back Wall 1 in the groove of the back rail and push it flush against the left rail. Have a helper hold the back wall section. Orient Side Wall Section 1 and place it in the groove of the left rail. Push the flat edge flush against back wall section. Align the two panels so they are flush and fasten them using the 4.5×70 screws
Vent holes on top!
Pre-drill the holes for the screws
Back Wall 1
Side Wall 1 Screws 4.5×70
Step 5. Position Back Wall sections 2 & 3, & Side Wall 1
Position Back Wall 2 section into the groove of the back rail. Attach it to Back Wall Section 1 by way of the tongue and groove fit. Secure it by tapping it into place with a rubber mallet. Repeat this step for wall section 3, again tapping it into place with a rubber mallet. Position Side Wall Section 1 into the groove of the right side rail and push flush against the back wall. Be sure panels are flush with each other and fasten them together using the 4.5×70 screws.
Pre-drill holes for the screws
Side Wall 1 Screws 4.5×70
Back Wall 2 Back Wall 3
Step 6. Position Side Wall Section 2, Window Section & Door Element
Position Side Wall Section 2 into the groove of the side rail. Slide Side Wall Section 2 into place with Side Wall Section 1. Section 2 connects to Section 1 via tongue and groove so there is no need to use screws. Use a rubber mallet to secure the fit.
Place Window Section in the groove on the front rail and push against side rail. Being sure the two sections are flush, fasten them together using 4.5×70 screws.
Place Door Section onto the front rail orienting it so that the door opens according to your preference. Door Section connects to window section via tongue and groove so there is no need for screws. Gently tap it into place with a rubber mallet to secure the fit.
Side Wall 2 Screws 4.5×70
Window
Door Element
Step 7. Position Window section and Side Wall section 3
Position Side Wall Section 3 into the groove of the Side Rail orienting it so that the heater vent holes are located at the bottom. Slide the wall section into place with Side Wall section 1. Side Wall 3 connects to Side Wall 1 via tongue and groove so there is no need to use screws. Use a rubber mallet to secure the fit. Next, place Window Section into the groove of the front rail and connect it to Door Section via the tongue and groove fit. Gently tap into place with a rubber mallet to secure the fit. Now, making sure Window Section and Side Wall 3 are flush with each other, secure them together with the 4.5×70 screws.
Pre-drill holes for the screws
Window Screws 4.5×70
Step 8. Assemble and Position Roof Support Rails
Reference step 2 and connect Roof Support Rails in the same way. Place the assembly on top of the wall sections so that the wall sections fit snugly into the groove. When in place, secure to the assembly to the walls using four 4×50 screws on each rail.
Roof Support Rail
Side Wall 3
Screws 4×50
Step 9. Bench and Lower Bench installation
Use 4.5×70 screws to connect the Bench Supports to the wall. Make sure the supports in both walls are the same height. When the supports are assembled, place the benches on the supports. Use three 4.5×70 screws to connect the Seat Bench to the Back Wall.
16.1″ 32.6″
20.3″
Screws 4.5×70
Screws 4.5×70
Step 10. Backrest Installation
Center the Backrest between the two sides and position it at a height most comfortable for you (typically 8-12″ from the bench). Use a level to ensure proper installation. Fasten the Backrest in place using 4×60 screws. Use 3.5×25 screws to connect the vertical slats to the backrest, refer to the dimensions on drawings. Now attach the Backrest between the upper and lower bench using 3.5×35 screws.
Screws 4×60 Step 1
Step2 2.1″
Backrest Screws 3.5×25
4,2″ Step3
Backrest Vertical Slat
Screws 3.5×35
Step 11. Side Bench installation
Attach the Side Bench Support 1 to the Lower Bench, using two 4.5×70 screws. The gap between the support and the side wall must be 2″. Side Bench Support 2 connects to the window section using 4×60 screws. Support must be in the same height with lower bench. Place the Side Bench on the supports and fasten with two 4.5×70 screws to the side wall element.
Pre-drill holes for the screws
Side Bench Support 1
Screws 4.5×70
Side Bench Support 2
Screws 4×60
Screws 4.5×70
Step 12. Lower Backrest installation
Using a level, secure the Lower Backrest to side wall section with 4×60 screws at the same height above the upper long bench.
Screws 4×60
Step 13. Position Roof Sections
Place the Roof Panels on top of the Ceiling Supports. Connect the sections via the tongue and groove fit. From the backside, roof panels must be in the same line with ceiling supports. Position both sides equally 1.625″. Connect panels with 4×50 screws.
Roof Section 1
Pre-drill holes for the screws
Roof Section 2 Screws 4×50
Step 14. Cornice Boards
Connect the Cornice Boards to the roof, using 3.5×40 screws.
Cornice Board 2 Screws 3.5×40
Cornice Board 2 Cornice Board 1
Pre-drill holes for the screws
Step 15. Vent Cover and Door Handle.
Connect Vent Cover with 3.5×40 screw. Between wall and Vent Cover add Small Washer.
Step 16. Heater Cover
Connect the Heater Cover to the wall with 4×60 screws. Perform this step after heater is installed. Note: Follow heater manufacturer recommended installation for heater guard.
Pre-drill holes for the screws
Screws 4×60 Step17. Cover Slats for the front wall
Connect the Cover Slats using 3.5×40 screws.
Cover Slat
Screws 3.5×40
REV: X603923
