X6 Indoor Home Sauna
Product Information: Model X6 Sauna Room
The Model X6 Sauna Room is a pre-fabricated sauna kit that is
designed to be assembled on any firm and flat surface, including
concrete, ceramic, vinyl, laminate, or tile. The kit includes
various components such as floor raisers, support rails, wall
sections, roof sections, bench, backrest, cornice board, heater
fence, footrest, vent cover, and door handle. The sauna kit is
specifically designed to utilize the existing floor and is easy to
assemble with the help of basic tools.
Product Usage Instructions:
- Read the entire installation and owner’s manual before
proceeding with the assembly. - Connect the four floor risers using 4.5 x 80 screws, ensuring
that the two shorter boards are located on the sides and the two
longer boards are on the front and back. - Connect the wall support rails using tenons and screws. Fasten
the rails together and connect from corners using four 3.5 x 20
screws per corner. - Lay the wall support rail assembly squarely on top of the floor
risers with the groove facing up. Secure the assembly to the floor
risers using four 4 x 50 screws evenly spaced on each wall support
rail. - Position the back wall section 1 in the groove of the back rail
and push it flush against the left rail. Have a helper hold the
back wall section. Orient side wall section 1 and place it in the
groove of the left rail. Push the flat edge flush against the back
wall section. Align the two panels so they are flush and fasten
them using 4.5 x 70 screws.
Note: The kit includes various components such as floor raisers,
support rails, wall sections, roof sections, bench, backrest,
cornice board, heater fence, footrest, vent cover, and door handle.
Basic tools required for assembly are cordless drill, tape measure,
rubber mallet, hammer, 1/2 or 5/8 Forstner bit, utility knife,
cordless screwdriver, screwdriver bits (Phillips & flathead),
level, step stool or ladder, and framing square. The installation
on a carpeted surface is not recommended.
Model X6 Sauna Room Installation Manual
saunalife.com 800.957.2862
X6 Sauna Model
Installation & Owner’s Manual
Congratulations on your purchase of the SaunaLife X6 model sauna! If you have any questions during assembly, please feel free to call us at 1-800-957-2862, or email [email protected]. Regular business hours are 8 am 5 pm, Central, M F.
Your SaunaLife X6 sauna is specifically designed to utilize your existing floor. As such, assembly is made very simple since the entire sauna sits on pre-fabricated rails and risers. Your sauna can be assembled on any surface that is firm and flat, including concrete, ceramic, vinyl, laminate or tile. Installation on a carpeted surface is not recommended.
SaunaLife X6 Kit Contents:
Floor raiser 1 (qty. 2)
Floor raiser 2 (qty. 2)
Support rail 1 (qty. 4)
Support rail 2 (qty. 4)
Back wall 1 (qty. 1)
Back wall 2 (qty. 1)
Back wall 3 (qty. 1)
Side wall 1 (qty. 2)
Side wall 2 (qty. 1)
Side wall 3 (qty. 1)
Roof 1 (qty. 1)
Window element (qty. 2)
Door element (qty. 1)
Bench (qty. 1) Side bench (qty. 1) Backrest (qty. 1)
Roof 2 (qty. 2) Bench support (qty. 2) Side bench support 1 (qty. 1) Side bench support 2 (qty. 1)
Lower backrest (qty. 1)
Cornice board 1 (qty. 1)
Cornice board 2 (qty.2
Read this entire manual thoroughly before proceeding with the assembly.
X6 Sauna Model
Installation & Owner’s Manual
Heater fence (qty. 1) Foot rest (qty. 1)
Front wall cover slat (qty. 2)
Vent cover (qty. 1) Door handle (qty. 1)
Tools required for assembly: Cordless drill Tape measure Rubber mallet Hammer 1/2″ or 5/8″ Forstner bit Utility knife Cordless screwdriver Screwdriver bits (Phillips & flathead) Level Step stool or ladder Framing square
Screws
Qty.
4.5 x 80 mm (.19″ x 3.14″) 8
4.5 x 70 mm (.17″ x 2.75″) 44
4 x 60 mm (.15″ x 2.36″) 8
4 x 50 mm (.15″ x 1.96″) 48
3.5 x 40 mm (.13″ x 1.57″) 26
3 x 20 mm (.11″ x .78″)
16
Vent Cover Washer
1
Tenon
8
saunalife.com 800.957.2862
STEP 1.
Connect the Four Floor Risers
Fasten the four Floor Risers together using 4.5 x 80 screws, being sure the two shorter boards are located on the sides and the two longer boards are on the front and back. Use a framing square to ensure the assembly is square.
Floor Raiser 1
Floor Raiser 2
Screws 4.5 x 80
Floor Raiser 2
Floor Raiser 1
Pre-drill holes for the screws
saunalife.com 800.957.2862
STEP 2.
Connect Wall Support Rails
Each wall support has a pre-drilled slot for a Tenon. Insert the tenons in the longer support rail holes. Fasten the wall support rails together and connect from corners using four 3.5 x 20 screws per corner.
Support Rail 1 Support Rail 2
Tenon
Support Rail 1
Tenon
Support Rail 2
Support Rail 1
Screws 3.5 x 20
STEP 3.
Position Wall Support Rails
Lay the wall support rail assembly squarely on top of the floor risers with the groove facing up. The rails should overlap both sides of the riser by approximately 0.5″. Secure the assembly to the floor risers using four 4 x 50 screws evenly spaced on each wall support rail.
Screws 4 x 50
STEP 4.
Position Wall Sections (Back Wall 1 & Side Wall 1)
Position Back Wall Section 1 in the groove of the back rail and push it flush against the left rail. Have a helper hold back wall section. Orient Side Wall Section 1 and place it in the groove of the left rail. Push the flat edge flush against back wall section. Align the two panels so they are flush and fasten them using 4.5 x 70 screws.
Vent Holes on Top
Pre-drill holes for the screws
Back Wall 1
Screws 4.5 x 70
Side Wall 1
STEP 5.
Position Back Wall Sections 2 & 3, & Side Wall 1
Position Back Wall 2 section into the groove of the back rail. Attach it to Back Wall section 1 by way of the tongue and groove fit. Secure it by tapping it into place with a rubber mallet. Repeat this step for Wall Section 3, again tapping it into place with a rubber mallet. Position Side Wall Section 1 into the groove to the right side rail and push flush against the back wall. Be sure panels are flush with each other. Fasten them using 4.5 x 70 screws.
Pre-drill holes for the screws
Side Wall 1
Screws 4.5 x 70
Back Wall 3
Back Wall 2
STEP 6.
Position Side Wall Section 2, Window Section & Door Section
Position Side Wall Section 2 into the groove of the side rail. Slide Side Wall Section 2 into place with side Wall Section 1. Section 2 connects to Section 1 via tongue and groove so there is no need to use screws. Use a rubber mallet to secure the fit.
Place Window Section in the groove on the front rail and push against side rail. Be sure the two sections are flush and fasten them using 4.5 x 70 screws.
Place Door Section onto the front rail orienting it so that the door opens according to your preference. Door Section connects to Window Section via tongue and groove so there is no need for screws. Gently tap it into place with a rubber mallet to secure the fit.
Side Wall 2
Screws 4.5 x 70
Window
Door Element
STEP 7.
Position Side Wall Section 3 & Window Section
Position Side Wall Section 3 into the groove of the side rail so that the heater vent holes are located at the bottom. Slide wall section into place with Side Wall Section 1. Side Wall 3 connects to Side Wall 1 via tongue and groove so there is no need to use screws. Use a rubber mallet to secure the fit.
Next, place the Window Section into the groove of the front rail and connect it to the Door Section via the tongue and groove fit. Gently tap into place with a rubber mallet to secure the fit.
Now, making sure Window Section and Side Wall 3 are flush with each other, secure them with 4.5 x 70 screws.
Pre-drill holes for the screws
Window
Side Wall 3
Screws 4.5 x 70
saunalife.com 800.957.2862
STEP 8.
Assemble & Position Roof Support Rails
Connect Roof Support Rails in the same way as Step 2. Place the assembly on top of the wall sections so that the wall sections fit snugly into the groove. When in place, secure to the assembly to the walls using four 4 x 50 screws on each rail.
Roof Support Rail
Screws 4 x 50
30.75″
STEP 9.
Bench Installation
Use 4.5 x 70 screws to connect the Bench Supports to the wall. Make sure the supports in both walls are in same height. When the supports are assembled place the bench on the supports. Use three 4.5 x 70 screws to connect the seat bench to the back wall.
Bench Support
Screws 4.5 x 70
Screws 4.5 x 70
STEP 10.
Side Bench Installation
Attach the Side Bench Support 1 to the back wall using two 4.5 x 70 screws. Side Bench Support 2 connects to the Window Section using 4 x 60 screws. Place the side bench on the supports and fasten wit three 4.5 x 70 screws to the side wall element.
Pre-drill holes for the screws
16.1″
Screws 4.5 x 70
Side Bench Support 1
saunalife.com 800.957.2862
X6 Sauna Model
Installation & Owner’s Manual
Side Bench Support 2 Screws 4 x 60
Screws 4.5 x 70
saunalife.com 800.957.2862
STEP 11.
Backrest & Lower Backrest Installation
Center the Backrest between the two sides and position it vertically at a height most comfortable for you (typically 8-12″ from the bench). Using a level to ensure proper installation, fasten the Backrest into place using 4 x 60 screws. Using a level, secure the Lower Backrest to side wall section with 4 x 60 screws at the same height above the upper long bench.
Backrest
Pre-drill holes for the screws
Screws 4 x 60
X6 Sauna Model
Installation & Owner’s Manual
Lower Backrest Screws 4 x 60
saunalife.com 800.957.2862
STEP 12.
Position Roof Sections
Place the Roof Panels on top of the ceiling supports. Connect the sections via the tongue and groove fit. From the backside, roof panels must be in the same line with ceiling supports. Position the both sides equally 1.875″. Connect panels with 4 x 50 screws.
Roof 1
Roof 2
Roof 3
Screws 4 x 50
Pre-drill holes for the screws
saunalife.com 800.957.2862
STEP 13.
Cornice Boards
Connect the Cornice Boards to the roof, using 3.5 x 40 screws.
Cornice Board 2
Cornice Board 2
Cornice Board 1
Screws 3.5 x 40
saunalife.com 800.957.2862
STEP 14.
Cover Slats to the Front Wall
Connect the Cover Slats using 3.5 x 40 screws
Cover Slat
STEP 15.
Heater Fence
Connect the Heater Cover to the wall with 4 x 60 screws. Perform this step after heater is installed. Note: Follow heater manufacturer recommended installation for heater guard.
Pre-drill holes for the screws
Screws 4 x 60
STEP 16.
Vent Cover & Door Handle
Connect the Vent Cover with 3.5 x 40 screw. Between wall and Vent Cover add small washer. Washer
saunalife.com 800.957.2862
STEP 17.
Foot Rest Installation
Connect the Foot Rest with 4.5 x 70 screws from one side to the Side Bench and from the other side to the side wall. Two screws per side. Measure from front wall must be 22.14″
Screws 4.5 x 70
Foot rest
Floorplan View
20″
saunalife.com 800.957.2862
Home - SaunaLife
