Saunalife E7g Sauna Barrel Glass Front Instruction Manual

E7G Sauna Barrel Glass Front

Product Information

The Ergo-Series E7G Barrel Sauna is a full glass-front sauna
measuring 71 inches in diameter and 81 inches in height. It comes
with front and back walls and requires assembly. The sauna is
designed with various components, including brackets, staves,
cradles, screws, and tools such as a measuring tape, marker pen,
circular saw, water level, hammer, ratchet strap, extra hands,
silicone gun (only for glass-wall models), drill, crescent wrench,
utility knife, and rubber mallet. The sauna also requires
waterproof silicone to be applied to the groove of the glass wall
during installation.

Product Usage Instructions

Before using the Ergo-Series E7G Barrel Sauna, please read the
manual carefully and follow the instructions for construction. Here
are the steps to install the front glass wall:

1. Use a scrap piece of wood to protect plywood and apply
   waterproof silicone to the groove.
2. Mount the glasses carefully and fix them diagonally to make the
   wall more rigid during installation.
3. Proceed with the main manual until benches installation.
4. Fasten screws under the benches on both sides. Drill holes
   before screws and pre-drill holes before fixing them.
5. Install the wooden back wall assembly with brackets inside.
   Pre-drill holes before screws.
6. Join two boards together that will bridge the width of the gap.
   It is recommended that the combined boards are approximately 1/4
   wider than the gap.

It is important to note that the sauna wall configuration
depends on your model. Be sure to leave a 1/4 gap when tightening
screws to leave room for adjustment when the outer bands (B) are
installed. Also, use straps to support boards during installation
and check the walls installation manual on extra pages for further
guidance.

Ergo-Series E7G Barrel Sauna Full Glass Front 71D” x 81H”

Note: Please read manual before construction

Rev 4/2023

Front & Back Walls

E7G Barrel Sauna 71D” x 81H”

Details list.

1

A

2

3

6

6a 6b

6c 6d

10

63″ x 8″ x 3¾” 51³/”
(x2) (x2) L=~256″
(x2)
B1
(x4)
G

·

63″

·

78″ x 1″ 59¹/” ·

70″

·

86″

x

4²³/” x 1″ 59¹/” · 70″

·

86″ x 1″ 59¹/” ·

70″

·

86″ x 1¾” 59¹/” ·

x 1″ 70″ · 86″
59¹/”

x ·

17″0x “15·9¹8″/6” “·x710³/”59·”¹/8×61″·””x703/4″”·x816″”

x 3/8″ x 1″ 51³/” · 63″

·

78¾”

x

20¹¹/”

(x1)

(x1)

(x2) (x1)

(x1) (x1)

B

Y

W Z

3¹/1″ x51b(” x12″)

X

x2 drain set

20

25¹/ x
(x2)

3¹1/5″ x a1″
(x2)

15c

27/x 1″ x 1″ 32¹¹/ x 3¹/”

x

15d
1″

(x1)

59¹/” · 70″ · 86″ x 2″

x

2″

22

(x2)
10a

18½”

x

1¾”

x 1¾”
10c

(x2)

5″ x 1¾” x 1¾”

(x2)

O

N

x 3¹/” 50″ · 61¹³/” (x2)

·

77/” H

x

15³/” M

11
x 3/”
D

C

” x 1¼ ” x 1½” ³/” x 2″ /” x 2¼” ³/” x 3½” L=~9″

(x1)

20d (x2)

20b (x2)

(x2) 25

(x38/50/62) (x5/7/8)

I J K L

(x4)
E

F
(x3)

(x1)

20c (x2)

20a (x2)

L=~17³/
(x16)

Bit PH2

Torx bits

T10 T15 T20 T25

~2lbs. (x15) (x90) (x45) (x150) (x50)

(x4) (x2)

Tools needed

Measuring tape Marker pen Circular saw

Water level

Hammer

Ratchet strap

Extra hands
Silicone gun (Only glass-wall models)

Drill

Cresent wrench

Utility knife Rubber mallet

Front glass wall installation

Thickness 1 ¹/”

1

2

3a

3b

4b

4a

x1

x1

x3

x3 x2

x2

x2

Thickness ”

12

3

x2

x2 x2

4 x2

U 5

76″ x 3¾” x 1″

TL1

Silicone

18½”

x11¾0″ xa1¾” 10c
5″ x 1¾” x 1¾”

x1

x2

x2

Baseframe 1 ¹/” ~3 /” Top
2x DET 4b

Use scrap piece of wood DET 1 to protect plywood

Apply waterproof silicone to the groove

DET 2

3x DET 3a

3x DET 3b

2x DET 4a

I

Bottom

~5 /”

II

1.

Front glass wall installation

Mount carefully glasses.

~/”

~/”

I
Coverframe ¹/” 2x DET 2 Top
2x DET 4
2x DET 1

II 2.

Bottom
2x DET 5 2x DET 3

~/”
Use scrap piece of wood to protect plywood
III

Front glass wall installation

~²/”

I Apply waterproof silicone to the groove

40x J

III 3.

II
min.²/”
CAUTION! Do not hit the glass with the screw.
Install front glass-wall same way as instructed in main manual.
IV

Front glass wall installation
DET U Fix it diagonally to make wall more rigid during the installation.
Proceed with main manual until benches installation!

4x DET 10a
4x H

2x I

I
Under the benches both sides.

WARNING: Do not let screws touch glass!
II

2x DET 10
Fasten screws under the benches on both sides

Drill holes ” before screws.
4x DET 10c

Pre-drill holes ”

10x I

Pre-drill holes ”

8x H

4x H
III 4.

CAUTION! Do not hit the glass with the screw.

2x I

Wooden back wall assembly

Details

U

76″ x 3¾” x 1″
TL1

x1

DET U
4x I
II
Pre-drill holes 5/32″ before screws.
Brackets inside.

2x H

Install front glass-wall same way as instructed in main manual.
III

E7G Barrel Sauna 71D” x 81H”

4x M

DET 1

2xDET A
DET 1
1.

51³/” · 63″ · 78¾”

Diagonal measurements should be equal 63″
4x M

E7G Barrel Sauna 71D” x 81H”

8x DET 3

Center stave 2 on cradle 1
Position cradles inside
grooves of stave 2

W

II

Y

Z X

2x M

mm=mm

DET 2

I

2.

3

2 33a

E7G Barrel Sauna 71D” x 81H”
I
16x M
II
3.

E7G Barrel Sauna 71D” x 81H”

Drill 4 holes Ø1/2″ through DET 2 outside

6x H
3xDET 3
Fix temporarily to support walls.
Use waterlevel
II
4.

90°
I
Check walls installation manual on extra pages! Sauna wall configuration depends on Your model! Brackets inside
~1/4″
IMPORTANT! Be sure to leave a 1/4″gap when tightening screws to
leave room for adjustment when the outer bands (B) are installed.

4x H

E7G Barrel Sauna 71D” x 81H” Remove
temporary bracing
H

DET 3

I

~1/4

Important! Leave space

H

IMPORTANT! Be sure to leave a 1/4″

gap when tightening screws to leave

room for adjustment when the outer

bands (B) are installed.

Strap
Use strap to support boards during installation

See the next page. DET 3

III

5.

II

E7G Barrel Sauna 71D” x 81H”

6 6a 6b 6c 6d

3
A I

3
Join two boards together (as shown in diagram II) that will bridge the width of the “A” gap. It is recommended that the combined boards are approximately 1/4″ wider than the gap.
Raise slightly before installing the combined board

DET 6
If needed, trim the flat edge of the board to create the desired width.

4
Fasten the two halves using screws
II
6.

III

E7G Barrel Sauna 71D” x 81H”
DET B1

~9/”

~5″

I
2x DET B

DET B

II 7.

Place the bands around the barrel on the outer
side of the cradle.
III

DET B1

Remove strap

DET B

E D
C

E7G Barrel Sauna 71D” x 81H”
Remove all
temporary braces

1x DET G

6x K

Pre-drill holes Ø5/32″ before screws.

I
2x DET 10a
2x H

Upper vent

3x DET F

Lower vent

6x K

72″ and 88″ Saunas with front-glass wall have 4 pc. of DET 10a.

8.

II

2x DET 10

NB! If Your sauna equipped with front-glass wall, see front-glass wall installation manual for proper benches installation.

III

E7G Barrel Sauna 71D” x 81H”

Pre-drill holes 1/8″

10x I

10x I
I
72″ & 88″ Saunas with front-glass walls have four pieces of 10c.

Use level for installation of benches
2x DET 11

2x H

Under the benches

9. II

4x H
2x DET 10c

6x M
III

E7G Barrel Sauna 71D” x 81H”
2x J
2x DET 15a

2x H

2x DET 15b

If needed – To accommodate

the size of your heater, trim

15A on the end that meets

the back wall, before adding

part H

I

2x DET 15c

Mount sauna heater before installing safety rail, per manufacturer’s recommended safety clearance

1x DET 15d

10.

II

6x I 2x J

Use waterlevel! Fasten door from inside.
~39″

E7G Barrel Sauna 71D” x 81H”
2x M

X= Front wall thickness Wooden front wall 1″ Glass front wall 1″

X
1x DET 20 2x DET 20c 2x DET 20d

I
2x DET 20a 2x DET 20b

X

2x M

Ensure door frame is pressed

II

tightly against the wall and

fasten from inside

18x H

16x J
11. III

8x H

2x DET 22
IV

8x H

E7G Barrel Sauna 71D” x 81H”
See the installation manual inside the shingles package

DET N

Overlap shingles on top
DET O Cut off
12. II

I
L

~”
Check also roof shingles installation manual inside package.

Cut DET N into three equal segments

Cut and use other end.

DET N

III

E7G Barrel Sauna 71D” x 81H”
8xDET 25

8xDET 25

16x H
I

16x H

13.

II

Remove DET A