2792-695/66A Auresa 2-Light Vanity Light
Product Information
Item number: 2792-695/66A
Date of manufacture: April 15, 2022
Fixture type: Wall or smooth fixture
Bulb type: Candelabra (T8)
Maximum wattage: 40 watts per bulb
Product Usage Instructions
Step 1: Shut off power at the fuse box or
circuit breaker and remove the old fixture including the mounting
hardware.
Step 2: Unpack the new fixture and lay out all
parts on a clean area. Take care not to lose any small parts
necessary for installation.
Step 3: Thread mounting screws (B) into
pre-drilled holes on circular strap (G) spaced same distance apart
as holes in back plate and tighten with nuts (E). The length of
mounting screws (B) may be adjusted if necessary.
Step 4: Attach circular strap (G) to junction
box using junction box screws (D). The side of circular strap
marked GND must face out.
Step 5: Connect the electrical wires as shown
in Fig.2, making sure that all wire connectors (C) are secured. If
your junction box has a ground wire (green or bare copper), connect
the fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the circular strap (G) using the green
screw provided.
Step 6: Tuck wire connectors neatly into the
junction box.
Step 7: Place back plate (H) over mounting
screws (B) and secure with finials (A).
Step 8: Install (2) two candelabra (T8) bulbs
up to 40 watts each in accordance with the fixture specification.
DO NOT EXCEED THE MAXIMUM WATTAGE RATING.
Step 9: Screw glass (F) onto the socket. Don’t
over tighten.
Step 10: Turn on power at the junction box and
test the fixture.
Note: Illustration (Fig.1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
Fixture Wires: White or Ribbed (Neutral), Green
or Bare Copper (Ground)
House Wires: Black (Hot), White (Neutral),
Green (Ground)
INSTALLATION INSTRUCTIONS
Item#2792-695/66A (New. 04/15/2022)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1) 1. Shut off power at the fuse box or circuit breaker and remove
the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts on
a clean area. Take care not to lose any small parts necessary for installation.
Fig.1
Set# A-021 -Circular Strap -Ground Screw -Mounting Screw*2
3. Thread mounting screws (B) into pre-drilled holes on circular
strap (G) spaced same distance apart as holes in back plate
and tighten with nuts (E). The length of mounting screws (B)
may be adjusted if necessary.
4. Attach circular strap (G) to junction box (not included) using junction box screws (D). The side of circular strap marked “GND” must face out.
CONNECTING THE WIRES (Fig.2)
C
5. Connect the electrical wires as shown in Fig.2, making sure
that all wire connectors (C) are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the circular strap (G) using the green screw provided.
6. Tuck wire connectors neatly into the junction box FINISHING THE INSTALLATION (Fig.1) 7. Place back plate (H) over mounting screws (B) and secure
with finials (A).
8. Install (2) two candelabra (T8) bulbs (not included) up to 40 watts each (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
9. Screw glass (F) onto the socket. Don’t over tighten.
F G D
E B
H A
Your installation is now complete. Return power to the junction box and test the fixture.
Fig.2
FIXTURE WBlaIRcEk Sor Smooth
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
FIXTURE WIRES White or Ribbed
HOUSE WIRES Black (Hot)
FIXTURE WGrIeReEnSor Bare Copper (Ground)
WHIORUESSE White (Neutral)
HOUSE WIRES Green (Ground)
2792-695
